Today’s wireless speakers often face a situation where the right and left earbuds stop syncing with each other, becoming two independent devices. This is a common problem, typical of the Xiaomi Mi True Wireless Earbuds Basic, which requires intervention in the logic of the Bluetooth module. Instead of transmitting sound in stereo, gadgets begin to play tracks separately, making comfortable listening to music impossible.
Reconnecting devices is not a complicated process, but requires a strict sequence of actions. You need to completely reset the current pairing settings and re-initiate the search for devices with each other, bypassing the smartphone. TWS-The headphones will work again as a single system.
In this article, we will take a detailed look at the algorithm for reconnecting left and right channels, and we will look at standard methods, forced resets, and solutions for the rare cases where standard procedures fail.
Why the headphones stop working in pairs
The main reason for desynchronization is a violation of the communication protocol between modules inside the case or when retrieving. Often this happens when the user removes the headphones from the charging case not simultaneously, but with a delay, or when one of the devices discharges faster than the other, at which point the Bluetooth module loses synchronization and goes into a waiting mode for a new source to connect.
Problems can also arise from software failures in the firmware of the headset or conflicts with the last connected smartphone. If the phone has an old profile with erroneous parameters in memory, the device may try to restore it, ignoring the search for a second headphone, Understanding the nature of the problem helps to find a solution faster.
Sometimes it is caused by contamination of contacts or oxidation, which prevents correct charging and initialization when placed in the case. Make sure that the metal spots on the headphones themselves and inside the case are clean. Dirt or moisture can block the signal to start the charging process, which makes the gadget not “wake up” correctly.
⚠️ Warning: Do not try to connect the headphones while they are inside the charging case.The primary synchronization process always takes place outdoors, away from the charge source.
Preparation for device synchronization
Before you start to actively pair, you need to perform a number of preparatory activities, which is a critical step, because the presence of old profiles in the memory of the phone can prevent the proper connection between the headphones themselves, you need to clear the field for a new configuration.
First, pick up your smartphone and go to Bluetooth settings.Look for the Xiaomi Mi True Wireless Earbuds Basic or Mi True Wireless EBs on the list of previously connected devices. Basic_R. Click on the gear icon or device information and select the option “Forget device” or “Disable".
After deleting the profile, it is recommended to completely turn off the wireless module on the phone, which will prevent one of the headphones from automatically connecting to the smartphone during their mutual adjustment, and now your gadgets are ready for the procedure of resetting and re-merging.
💡
Before starting the procedure, make sure that both earbuds are at least 50% charged. Low battery power can cause the synchronization process to interrupt halfway.
Make sure both earbuds are off. If the lights are on, place them in the case, close the lid, wait 5 seconds and remove them simultaneously, ensuring they start from the same state.
Step-by-step: how to connect the left and right headphone
The most effective way to restore communication is to manually start pairing on one of the devices, and normally the right earpiece acts as a master device, which then broadcasts the signal to the left, and you need to be careful and follow the timings accurately.
Remove both earphones from the charger case, and they should automatically turn on, as the flashing light signals, at which point they are not yet connected to each other and operate independently.
☑️ Checklist for mating preparation
Now, follow the following steps to force synchronization:
- 🔘 Press and hold the touch panel on the right earpiece for a period of time. 5-7 It will be a few seconds before it is turned off (the indicator will go out).
- 🔘 Immediately after turning off, press and hold the touch panel again, but now hold near 15-20 seconds.
- 🔘 The indicator should flash red and white several times, and then start flashing only white with a lower frequency.
- 🔘 This means that the right earphone went into the search mode of the left "brother".
After the right earphone is in standby mode (slow white blinking), tap the left earphone touchpad once, and it should start flashing white quickly, and then both lights should go out or go into rare blinking mode, signaling a successful connection.
💡
Successful synchronization is confirmed by the fact that the indicators on both headphones go out or start flashing synchronously every few seconds, and only one device appears in the phone’s Bluetooth list.
Alternative method of discharge through the case
If manual synchronization through long-term retention failed, you can try a reset method using a charging case, which often helps when a software failure blocks standard control commands, and it is more radical and restarts the power controller.
Place both earbuds in the charge case. Make sure they're sitting tight in the sockets and the contacts are in contact. The indicators on the devices should light up, signaling the start of charging. Leave them in this position on the back of the headset. 10-15 seconds.
Then, without closing the case cover (if it's transparent or you can see the indicators), press and hold the touchpads on both headphones simultaneously for 20 seconds. The indicators should flash red several times.
| Status of the indicator | Meaning | Action. |
|---|---|---|
| Blinking red/white | Interconnection mode | Wait for the connection. |
| Slowly flashing white | Waiting for connection | Turn on Bluetooth on your phone |
| Red is burning. | Charging's coming. | Leave it in the case. |
| It's not burning. | Switched off or discharged | Charge or switch on |
⚠️ Note: During the reset procedure, do not bring your headphones too close to running Wi-Fi routers or microwave ovens. interference in the 2.4 GHz range can interrupt the synchronization process.
Connection to the phone after recovery
Once you successfully connect your left and right headphones, you need to connect them to your smartphone. Now, the list of available Bluetooth devices should only show one name, not two separate ones (L and R).
Turn on Bluetooth on your mobile device and start searching for new gadgets. In the list, find Xiaomi Mi True Wireless Earbuds Basic. Click on the name to connect. If the system requests a pairing confirmation, agree with it.
Once you've successfully connected, check the sound. Turn on the music and take the earbuds out of your ears in turn. The sound should be stereo and be present in both channels. If the sound comes from only one channel, repeat the reset procedure again, doubling the time you hold the button.
Sometimes you need to restart your smartphone to fully update your Bluetooth service list. If the connection is successful but there is no sound, check your media settings on Android or iOS to make sure that the audio output is directed to the headset.
Problem Solving: What to Do When Nothing Helps
In rare cases, standard methods may fail due to a deep software failure or hardware problems. If none of these methods helped to combine devices, it is worth trying more complex diagnostic options.
Leave both earbuds off the case until they are completely discharged and turned off. Then place them in the case to charge for a few hours. After full charging, try to do the pairing again. This cold reboot method sometimes clears errors in the controller's memory.
It's also worth checking if the problem is hardware, and if one of the headphones doesn't respond to touch at all, or if the light doesn't turn on, the battery or the touchpad may have failed, and then the software methods are powerless.
If the problem persists, consider using the Mi Wear app or Xiaomi Earbuds. Although basic AirDots models often don't support these apps directly, in some cases, updating firmware through compatible apps can fix communication bugs.