How to tie the remote to the TV Xiaomi: all the ways + fixing

Assimilating the remote to a Xiaomi TV is a procedure that every owner faces after buying a device or replacing a remote. Despite its apparent simplicity, the process can be difficult: the TV does not respond to commands, the indicator on the remote does not flash, and the instructions do not contain details for your model. In this article, we will discuss all the current ways of synchronization, from standard binding of the original remote to setting up universal devices and solving typical errors.

Feature of Xiaomi TVs (series Mi) TV 4/5, Redmi Smart TV, Mi TV Q1/Q2) — Using Bluetooth remotes instead of infrared, which means that communication requires not only "direct visibility," but also the correct setting of the wireless module, so if you bought a used TV or remote control separately, the procedure may be different from the factory one. Below you will find step-by-step instructions for all scenarios, including forced re-binding when synchronization fails.

1.Preparation: What to check before binding

Before you start syncing, make sure there are no hardware issues. Often users spend hours setting up when the cause is dead batteries or mechanical damage.

Here is the mandatory checklist before binding:

• 🔋 Check the batteries in the remote: even if the indicator is on, the voltage may not be enough for stable communication).
• 📺 Make sure the TV is on and running. If the screen doesn't respond to the power button on the case, the problem may be the power supply.
• 📶 Disable other Bluetooth devices nearby (earphones, speakers, smartphones) that can interfere at 2.4 GHz.
• 🔄 If the remote was previously tied to another TV, reset (click Menu) + OK 10 seconds before the indicator flashes).

Replace your batteries with new ones (even if the old ones are working"|

Make sure the TV is plugged in and the indicator is on.|

Disable other Bluetooth devices within a 5-meter radius|

Check the remote for mechanical damage (cracks, moisture)|

Reset the previous tether (if the remote was used with another TV)

-->

If you use a universal remote (such as Xiaomi Mi Remote or third-party models), make sure it supports Bluetooth protocol. LE. Remotes with an IR transmitter (infrared) will not be suitable for most modern Mi TV, Except for older models until 2018.

⚠️ Attention: On Xiaomi TVs with Android TV 9.0 and later (released after 2020) disabled support for IR remotes at the hardware level. IR remote will result in the "No signal" error.

2. Standard binding of the original Xiaomi remote

This method is suitable for new remotes that come bundled with a TV. If you bought a Mi TV, it's a good idea. TV A2 "43" or "Redmi Smart" TV X55, The remote has never been used – follow this instruction.

The binding algorithm:

1. Turn on the TV with a button on the case (usually located on the side or bottom).
2. Press and hold the Menu buttons (⋯) + OK on the remote simultaneously for 5-7 seconds, until the indicator starts flashing double flashes.
3. Bring the remote to a distance of 10-20 cm to the TV (preferably to the upper right corner, where the Bluetooth module is located).
4. Wait for a single flashing of the indicator on the remote – this is a signal of successful synchronization.
5. Check the buttons: first Power, then Volume+ home.

For Mi models TV Q1/Q2 (2021–2026 d) the process is slightly different:

• 🔄 Instead of Menu + OK Use the Back combination (←) + Home (⊙).
• 🕒 The button retention time is increased to 10 seconds.
• 📱 After successful binding, a notification “Connected” will appear on the screen".

💡

If the TV doesn’t respond to the first attempt, try tying the remote in steam locomotive mode: press Power on the TV body, then hold the Menu right away. + OK This will work for 80 percent of the models with the gaggy Bluetooth.

3. Linking the universal remote to Xiaomi TV

Universal remotes (e.g. Xiaomi Mi Remote, BroadLink) RM4 Logitech Harmony requires a separate setup, the main difference being the need to choose the right protocol (Bluetooth or IR) and the device code.

Instructions for Xiaomi Mi Remote (Bluetooth):

1. Download the Mi Home app to your smartphone and add the remote to the list of devices.
2. In the application, select "Add device" → "remote" → "Television".
3. Follow the on-screen hints by holding the remote near your phone (not the TV!).
4. After synchronization with your phone, bring the remote to the TV and press Menu. + OK complete.

For IR panels (only for older Mi models) TV 3/4 2017–2019 garland.):

1. Find the code for Xiaomi in the remote manual (usually 0178, 0225 or 1178).
2. Hold the Setup on the remote until the indicator flashes.
3. Enter the code using digital buttons.
4. Press Power – if the TV is turned off, the setup is successful.

⚠️ Note: Universal remotes with Bluetooth 4.0 support (e.g. One For All) URC7960) You may not work with Xiaomi TVs on Android TV 11+ Check compatibility on the manufacturer's website before buying.

4. Forced re-binding of the remote (if the TV does not respond)

If the TV stopped responding to the remote after updating the firmware or crashing, a forced reset would be required, which works for 90% of cases where standard tethering doesn't work.

Step-by-step:

1. Turn off the TV (remove the plug) for 2 minutes.
2. Press and hold the Power button on the TV body for 15 seconds (this will discharge the capacitors).
3. Connect the power back and turn on the TV button on the case.
4. On the remote, pinch the Menu. + Back (←) + OK 12 seconds at the same time until the indicator flashes red.
5. Bring the remote to the TV at a distance of 5-10 cm and wait for a single green blink.

If the remote does not work after that:

• 🔧 Check if the connection is blocking. VPN Firewall on the TV (Go to Settings) → Network → Additionally).
• 📥 Update the TV firmware to the latest version (older versions have a bug with Bluetooth stack).
• 🔄 Perform reset to factory settings (Settings) → The device → Reset ), but note that it will remove all installed applications.

💡

Forced reassignment works even if the TV doesn't see the remote in the Bluetooth menu, which bypasses the standard pairing protocol and establishes a low-level connection.

5. Solving typical binding errors

The Xiaomi TV’s remote synchronization errors can be divided into three categories: hardware (hardware problems), software (software failures) and external (interference, network settings).

Mistake 1: The remote is flashing, but the TV is not responding

• 🔍 Check if the indicator on the front of the TV is on (if not, power problem).
• 📡 Move the TV and remote to another room – there may be a source of interference nearby (microwave, Wi-Fi router on channel 11–13).
• 🔄 Try to link the remote to another device (such as a smartphone via Mi Home) to rule out malfunctioning.

Error 2: The TV says "Device is not supported"

• 📋 Make sure the remote model is compatible with your TV (see table in Section 3).
• 🔧 In the TV menu, go to Settings → Devices → Bluetooth and manually remove all stored devices.
• 📱 Update the remote firmware (if it is a universal model) through the proprietary app.

Error 3: Remote works, but with a delay (lag)

• 📶 Reconnect your TV to a 5GHz Wi-Fi network (2.4GHz can interfere with Bluetooth).
• 🔋 Replace batteries with lithium (they last longer).
• 🧹 Clean the TV's cache: Settings → Annexes → Systemic → Clear the cache.

The remote is flashing, but the TV is not responding.|

TV doesn't find remote in Bluetooth menu|

The buttons are delayed (lag)|

The remote is tied, but not all buttons are functioning.|

Another problem.

-->

6.Configure the remote via the TV menu (alternative method)

If the standard binding doesn't work, you can try connecting the remote via the Bluetooth menu of the TV. TV 10.0 and newer.

Instructions:

1. Turn on the TV and go to Settings → Devices → Bluetooth.
2. Activate your search for new devices.
3. On the remote, press and hold the Menu. + OK before flashing indicator.
4. In the list of found devices, select "Mi Remote" (or the name of your model).
5. Confirm the pairing on the TV (entry may be required) PIN-code 0000 or 1234).

If the remote is not displayed in the list:

• 🔄 Restart the TV (Settings) → The device → Reboot).
• 📱 Make sure that Bluetooth settings enable the “Visible to all devices” mode".
• 🔧 Check if the Bluetooth TV module is disabled in the service menu (available by code 1147 on the standby remote control).

7.Tieting the remote to Xiaomi TV Stick or Mi Box

If you don’t have a TV, you have a Xiaomi console. TV The Stick or the Mi Box S, the process of synchronizing the remote will be different. These devices use a simplified Bluetooth protocol, and they do not fit universal remotes from TVs.

Instructions for Mi TV Stick:

1. Connect the set-top box to the TV via HDMI and turn it on.
2. On the original remote, pinch Home (⊙) + Back (←) 5 seconds.
3. Wait for the indicator to flash on the console (blue LED).
4. Press. OK link-up.

For the Mi Box S:

1. Go to Settings → Remote and accessories → Add an accessory.
2. On the remote, hold the Menu. + OK before appearing.
3. Select the device and confirm the pairing.

⚠️ Attention: Remotes from Mi TV The Stick and Mi Box are not interchangeable with Xiaomi TVs, even if they look the same.

8 What to do if nothing helps?

If you've tried all the ways, but the remote doesn't get attached, maybe the problem is a hardware malfunction.

Diagnosis of malfunctions:

• 🔧 Check the remote on another Xiaomi TV (at friends or in a service center).
• 📡 Test the Bluetooth module of the TV by connecting other devices (earphones, gamepad).
• 🔋 If the TV is not turned on from the remote or from the button on the case - the problem is in the power supply or motherboard.

Where to turn for help:

• 📞 Official support for Xiaomi in Russia: 8 800 775-66-88 (call-off).
• 🛠️ Authorized service centers (list on the website) mi.com/ru/service).
• 💬 Community of users on the forum 4PDA (section "Xiaomi TVs").

If the TV is guaranteed, do not disassemble it yourself - this will cancel the warranty obligations. In case of hardware failure (for example, the Bluetooth module failed), repairs will cost 1,500-3,000 rubles depending on the model.

💡

Before visiting the service center, take a picture of the serial number of the TV (located on the sticker at the back) and prepare a check - this will speed up the diagnostic process.

FAQ: Frequent questions about the remote