How to connect the remote to the TV Xiaomi: full instructions

Xiaomi’s modern Smart TVs come with advanced Bluetooth remotes that make multimedia content management much easier, and unlike older infrared models, they don’t require direct vision and allow voice search, but when you first set up or reconnect after you replace your batteries, you sometimes have questions.

In this guide, we will discuss in detail how to pair a Mi Remote remote with a TV, and how to solve typical problems, and how to activate search mode, check compatibility, and reset if the standard algorithm does not work.

Most new Mi TVs and Mi Sticks use a single communication protocol, making the setup process universal, and the key is to follow the sequence of actions and carefully monitor the display on the screen.

Preparation of equipment and compatibility check

Before you start the synchronization process, you need to make sure that your equipment is ready to go. First of all, check for fresh batteries in the remote control. Weak charge often causes unstable connection or inability to enter pairing mode.

Turn on the TV and make sure it works correctly. If you have a spare IR remote or control buttons on the TV body, use them to navigate the menu. For Bluetooth models, it is critical that the TV is in line of sight at a distance of no more than 2 meters during setup.

Make sure your remote does support Bluetooth, usually with a voice search microphone and a quick-assist button, and infrared models don't require complex pairing and work immediately after the batteries are installed.

⚠️ Note: Do not use old or partially discharged batteries when setting up Bluetooth devices. MAC-television addresses.

For successful configuration, you may need the following elements:

• 🔋 New alkaline batteries of the type AAA (usually 2)
• 📺 Xiaomi TV with Bluetooth support
• 🔦 Additional IR remote or access to buttons on the TV body
• 📱 Smartphone with Mi Remote (as a backup control option)

Standard procedure for pairing a Bluetooth remote

The main method of connection for most scenarios, when the remote is new or has been successfully untied before, takes no more than a minute and requires no special skills, the main thing is to activate the search mode on the remote itself correctly.

Press both at the same time and hold the two buttons: the menu (three stripes) and the back (arrow left).In some models, these can be the Home and Menu buttons. Hold them for about 5-7 seconds until the LED indicator at the top of the remote starts to blink quickly.

Once the indicator flashes, look at the TV screen. In the upper right or lower corner, a pop-up should appear with the message "New device found" or "Connect remote control". Press the OK button on the remote (if it already partially responds) or confirm the action with the control.

Once confirmed, a message will appear on the screen about the successful connection. Now your Xiaomi remote is fully functional and ready to manage the Android TV or PatchWall system.

Configure through the system menu of the TV

If an automatic pop-up doesn't appear, you can manually initiate a search through system settings, which is more reliable because it allows you to control the discovery process.

If you use the buttons on the TV body or remote control, go to the main menu. You need to find the settings section, which is usually indicated by the gear, and depending on the firmware version, the path may vary slightly.

Go to the following path: Settings → Remote and Accessories → Add Accessory. TV will go into active search for Bluetooth devices. At this point, repeat the procedure of activating the remote (hold buttons Menu + Back).

The list of available devices should show the name of your remote, for example, Mi Remote or Xiaomi Bluetooth Remote. Select it and click OK to complete the pairing.

Sometimes the system may request code confirmation, although this is rare on Xiaomi TVs. Just follow the instructions on the screen.

Table of button combinations for different models

Different generations of Mi Remote remotes may require different key combinations to enter pairing mode. Below is a table that will help determine the correct sequence of actions for your device.

Note that the button combination must be executed simultaneously. Press the keys clearly and hold them until the indicator behavior changes.

Using a Smartphone as an Alternative

If the physical remote is lost or no longer responding, a smart phone is a great solution, and emulator apps allow you to fully control the TV over a Wi-Fi network.

To do this, make sure your phone and TV are connected to the same Wi-Fi network. Download the official Mi Remote app (for Xiaomi phones) or Google Home/Android TV Remote Control (for other Android and iOS devices).

Launch the app and press the add-on button, and the program will automatically find your TV on the local network. PIN-code displayed on the TV screen, the phone will turn into a full-fledged remote with a touchpad and keyboard.

⚠️ Warning: Wi-Fi control only works if the TV is already connected to the network. If the remote problem occurs when you first set up the TV, this method will not work without connecting. USB-keyboard.

It's a great temporary way to regain control until you find or buy a new Bluetooth remote.The app's functionality is often even wider than that of a physical device.

Solving problems and resetting remote settings

In situations where the remote stops responding or permanently loses connection, a complete reset may be required, which will clear the pairing memory and allow the process to start again.

Reset the batteries from the remote. Press and hold any button for 10-15 seconds (without power, this will discharge the residual current). Insert new batteries and try to pair again.

If the problem persists, there may have been a software failure in the Bluetooth module in the TV. Try to perform a full system reboot: Settings → Device → About System → Reboot.

💡

If you have frequent communication interruptions, try to remove powerful sources of radio interference from your TV, such as Wi-Fi routers, wireless speakers or USB 3.0 hubs.

It’s also worth checking if the remote is connected to another device. Xiaomi’s Bluetooth remotes can remember the last device they connected to.

Frequently Asked Questions (FAQ)

💡

The stable operation of the remote depends not only on the batteries, but also on the absence of interference in the air and the relevance of the TV firmware.