How to connect the receiver to the Xiaomi TV: all the ways and settings

Connecting the receiver to a Xiaomi TV is a challenge that users face when switching to satellite, cable or digital TV. Despite its apparent simplicity, the process can cause difficulties, from choosing the right cable to configuring the signal source in the Mi menu. TV. In this article, we will discuss all the current ways of connection (through the HDMI, AV, SCART), nuances for different models of receivers and TVs Xiaomi, as well as typical errors that prevent you from getting a stable signal.

Special attention will be paid to modern Xiaomi TVs (series Mi). TV Q2, Redmi Smart TV X, Mi TV A2), So if you're using a receiver from a Tricolor, NTV Plus or MTS TV, the interface and connectors might be different from the old models, and if you're using a receiver from a carrier like Tricolor, NTV Plus or MTS TV, the instruction will also work -- the principles of connection are universal.

At the end of the article you will find FAQ answering frequent questions, such as what to do if the TV can’t see the receiver, how to adjust the sound through the HDMI ARC, Or why the image breaks. Let's start with the hardware.

1. What cables and connectors will be needed to connect

The first step is to determine which connectors are on your receiver and Xiaomi TV, which determines the choice of cable and the quality of signal transmission. TV Q2 2023 or Redmi Smart TV X55) commonly equipped:

• 🔌 HDMI (Priority option for Full HD/4K signal)
• 📺 AV (RCA, «Tulips – for old receivers
• 🖥️ SCART — It is rare but occurs in European models.
• 📡 Entrance (RF) — digitally (DVB-T2)

On the receiver, check for the same connectors. GS U510 or DRE-4000 have HDMI and AV, and cable receivers from Rostelecom - only HDMI. If the connectors do not match, you will need an adapter (for example, SCART → HDMI or AV → HDMI).

Important: for Dolby Digital audio transmission or DTS use HDMI ARC (This is true for Xiaomi models with Dolby Audio sound systems (e.g. Mi). TV P1).

Next Next post: If your Xiaomi TV is released before 2020 years (e.g. Mi) TV 4S), It may not have support. HDMI 2.1, That will limit the permission to 4K@30Hz when connecting modern receivers.

2. Connecting the receiver to Xiaomi via HDMI: step-by-step

This is the most reliable and high-quality method recommended for all Xiaomi models (from Mi). TV 4A before TV Q2). Use the cable. HDMI 2.0 or later for support 4K HDR.

Turn off the TV and receiver from the socket

Check the version. HDMI-Port of TV (written next to the connector)

Use a cable no longer than 3 meters long (for the purpose of 4K)

Connect the cable to the port HDMI IN on TV and on TV HDMI OUT receiver-->

After the physical connection:

1. Turn on the receiver and wait for its loading (the operator logo, for example, Tricolor, should appear on the console screen).
2. On the Xiaomi remote, click the Input (or Source) button.
3. Select the source of the signal — HDMI 1, HDMI 2, etc. (depending on the port where the cable is connected).
4. If the image does not appear, check if the mode is turned on. HDMI-CEC in the settings of the TV (Settings) → System system → HDMI-CEC). This will allow you to control the receiver from the Xiaomi remote.

Challenges and solutions:

• 🖼️ No image: Try another one. HDMI-port on the TV or replace the cable. In the receiver menu, check the permission settings (set the permission settings). 1080p instead 4K, if the TV does not support).
• 🔊 No sound: in the settings of the TV, select Settings → Sound. → Exit HDMI and set PCM (If the receiver does not support Dolby Digital).

💡

If, after connecting through HDMI picture "slows down", in the receiver menu, turn off the Deep Color function or reduce the bitrate to 8-bit.

3. Alternative ways of connecting: AV, SCART, RF

If you don’t have a Xiaomi TV or receiver HDMI, You can use analog connectors. Let's look at each option.

Connection through AV (RCA, «tulip»):

• 🔴🟡🔵 Connect the connectors. VIDEO (yellow), AUDIO L (white) and AUDIO R (red) with corresponding ports on TV and receiver.
• On the Xiaomi remote, select the source AV composite.
• Image quality will be limited 480p, stereo.

Connection through SCART:

This connector is rare, but if it is on the receiver (for example, in older models). DRE), use the adapter SCART → HDMI. The cost of such an adapter is from 500 rubles. After connecting to the TV menu, select the source. HDMI (Even if the signal is going through the adapter).

Connection through antenna input (RF):

Relevant for digital receivers DVB-T2 (For example, set-top boxes for 20 channels. Connect the cable from the receiver to the antenna input of the TV (RF IN), Then, on the Xiaomi menu, select the TV source or DTV. Channel settings are performed automatically through AutoSearch.

⚠️ Note: When connecting through AV or SCART on Xiaomi TVs with resolution 4K You may experience blurring, and this is due to low-resolution upscale to the screen. To reduce the effect, in the TV settings, turn off the option to Improve the image (Settings) → Picture → Additionally).

4. Set up the receiver on the Xiaomi TV: channel search and sound

After the physical connection, you need to configure the signal source and, if necessary, search for channels.

For satellite receivers (Tricolor, NTV-Plus, MTS TV):

1. On the receiver remote, press Menu. → Installation → Searching channels.
2. Choose the search type: Automatic (recommended) or Manual (if you need to add specific channels).
3. For Tricolor, enter the satellite parameters: Eutelsat 36E, frequency 12226 L 27500.
4. After searching, save the channels and restart the receiver.

For cable receivers (Rostelecom, Dom.ru):

Search settings are usually preloaded by the operator. You just have to select AutoSearch from the console menu. If channels are not found, check if the operator's cable is connected to the port. LNB IN receiver.

Sound setting:

• 🔊 If the sound goes through HDMI, in the TV menu (Settings) → Sound. → Exit, select HDMI or ARC (sound-system).

Typical problems and their solutions

Even with the right connection, there can be failures, and let's look at the most common ones and how to fix them.

Additional advice:

• 🔌 If the Xiaomi TV doesn’t turn on after the receiver is connected, check if the socket is overloaded (some consoles consume up to 30 watts).

⚠️ Attention: On Xiaomi TVs with Android TV (Like Mi. TV P1) when connecting the receiver through HDMI The Live Channels app can automatically start. To avoid this, in the application settings, turn off the Auto Start option when you connect the TV tuner.

6. Features of connection for different models Xiaomi

The interface and connectors may vary depending on the TV series, so let's look at the key nuances.

Xiaomi Mi TVs TV 4S/4A (2018–2020 garland.):

• They do. 2–3 port HDMI 2.0, not supportive 4K@60Hz.
• There is no section in the menu HDMI-CEC — Receiver control from the Xiaomi remote is impossible.

Xiaomi Mi TVs TV Q1/Q2 (2021–2023 garland.):

• Supporting. HDMI 2.1 (4K@120Hz), but for stable operation of the receiver it is better to limit 4K@60Hz.
• There's a function. ALLM (Auto Low Latency Mode – useful for gaming consoles, but can cause delays when watching TV. → HDMI.
• Dolby Vision supports, but not all receivers pass this format. Check compatibility in the console specifications.

Redmi Smart TVs TV X (2022–2026.):

• They have hybrid ports. HDMI/ARC — Allows sound to be broadcast to the soundbar via the same cable.
• The menu has a Smart Home section where you can link the receiver as a device (if Mi Home is supported).
• When connecting through AV Retro mode is automatically turned on to improve the quality of the old signal.

💡

On Xiaomi TVs with Google TV (Like Mi. TV A2) When you connect the receiver, you may notice an unidentified device. That's okay -- just confirm the connection in the dialog box.

7 How to improve signal quality and avoid interference

If the image snows, the sound is interrupted, or the channels periodically disappear, the problem may be a weak signal or interference.

For satellite receivers:

• 📡 Check the antenna alignment (plates) - even a slight shift can degrade the signal. Use the SatFinder app to fine-tune the settings.
• 🔗 Replace the cable from plate to receiver with low attenuation coaxial (marking) RG-6).
• 🛠️ Install a signal amplifier (e.g., Gecen) A21) plate-to-receiver.

For cable receivers:

• 🔌 Check if the operator’s cable is damaged (curves, incisions).
• 🔄 Restart the receiver and wait for the provider to update the data (it can take up to 10 minutes).
• 📞 Contact the operator (like Rostelecom) and request a line check – sometimes the problem is on their side.

For digital receivers (DVB-T2):

• 📶 Move the antenna closer to the window or higher. Use an active antenna powered by USB.
• 🔍 In the receiver menu, check the signal level (Menu). → Installation → Signal status. Optimal value is 80-100%.

General recommendations:

• 🚫 Avoid placing the receiver near sources of interference: microwaves, routers, wireless charging.
• 🔋 Use a network filter to protect against voltage surges.
• 📱 Update the receiver firmware (the instructions are usually on the operator’s website).

💡

If you see artifacts in the form of squares or stripes on the screen, try disabling Hardware Acceleration in the receiver menu (if there is such a item), this will help if the codecs are incompatible.

FAQ: Frequent questions about connecting the receiver to Xiaomi