Connecting a game console to a Xiaomi TV: full instruction with settings

Connecting a game console to a Xiaomi TV seems like a simple task, but in practice users face nuances: from choosing the right one to the right one. HDMI-This is especially true for modern consoles like PlayStation 5, Xbox Series X or Nintendo Switch, which require high cable bandwidth and specific display parameters.

Xiaomi Mi TVs TV redmi TV (series A2, P1, Q2, S Pro support HDMI 2.1, ALLM (Auto Low Latency Mode and VRR (Variable Refresh Rate), but these features are often disabled by default. In this article, we will discuss not only physical connectivity, but also image optimization for gameplay, solving problems with black screen or no sound, and nuances for older models of TV without the need to use the same name. HDMI 2.1.

If you're connecting for the first time or you're exposed to image artifacts after updating your TV firmware, here's a proven solution. For convenience, we've divided the instructions into steps, from choosing a cable to fine-tuning the Game Mode.

1.Cable and port selection HDMI: know-how

Quality. HDMI-cable depends not only on the resolution, but also the frame rate, support HDR and VRR. For modern consoles (PS5, Xbox Series X/S) The Ultra High Speed cable is required HDMI (certified 48Gbps). Old cables HDMI 2.0 permit 4K@60Hz and not 120 Hz.

Xiaomi's TVs have ports HDMI frequently marked:

• 🔹 HDMI 1 (eARC) – Optimal for sound systems, but not always the best choice for consoles.
• 🔹 HDMI 2/3 (Game - usually prioritize low latency (in Mi models) TV Q2 75" newer).
• 🔹 HDMI 4 – may be limited in bandwidth (check the TV menu).

Nintendo Switch (even in the docking station) is enough HDMI 1.4, But if you're planning on playing in 4K Switch OLED with third-party docks - take HDMI 2.0. Xiaomi TV series ES (2020 years not supported HDMI 2.1, therefore PS5 into 4K@120Hz You will need an external adapter.

⚠️ Note: Do not use cheap cables without Ultra High Speed certification – they can cause screen flickering or signal loss under high loads (for example, in God of War). Ragnarök on PS5).

2. Physical connection: step-by-step instruction

Turn off both the console and the TV before you connect, which will prevent conflicts when you recognize the signal.

1. Connect. HDMI-cable to the prefix port (for example, on the PS5 It's in the back, next to the power connector).
2. The other end of the cable is inserted into HDMI-TV port (preferably with Game marking or HDMI 2.1).
3. Turn on the TV and go to the signal source: on the Xiaomi remote, click Source (or Input) and select the appropriate one. HDMI-port.
4. Turn on the console. If the screen is still black, try another port or cable.

On Xiaomi models with Android TV (Like Mi. TV Q1E) You may notice a new device, confirm the connection. If the TV doesn't respond:

• 🔌 Check that the cable sits tightly in the connectors (characteristic click when connecting).
• 🔄 Reboot the console and TV (unplug the network for 30 seconds).
• 📺 On some Xiaomi models, you need to manually activate the port in the Settings menu → Connections → HDMI-control.

The cable is certified for 4K/120Hz|

Port port HDMI Labeled as Game|

The TV and console are turned off when connected|

Selected the right source of the signal on TV-->

⚠️ Note: On the Xiaomi TV series ES (2020) when connected PS5 You may need to disable Dolby Vision in your console settings – otherwise the screen will flash or display artifacts.

3. Setup of permission and frame rate

After successful connection, you need to optimize the display parameters. PS5 Xbox Series X is automatically adjusted, but sometimes manual adjustments are required:

For PlayStation 5:

1. Go to Settings. → Screen and video → Video output.
2. Select the Permission: 2160p (4K) or 1080p (if the TV does not support 4K).
3. Turn on 120Hz (if the TV supports).
4. Activate. VRR (if available, and ALLM.

For Xbox Series X/S:

1. Open the Settings. → General. → TV and display settings.
2. Set the Permission: 4K UHD.
3. Enable the Acceptable Update Frequency: 120 Hz.
4. Activate. VRR and ALLM.

On the Nintendo Switch in the dock:

1. Go to System Settings → TV.
2. Select TV Permission: 1080p (maximum for a standard dock).
3. Turn off Color Matching. RGB, if the colors look unnatural.

💡

If the Xiaomi TV doesn’t offer Game Mode automatically, turn it on manually: → Picture → Image mode → It'll reduce the input delay to 10 to 15 milliseconds.

4. Sound optimization: HDMI ARC, eARC and external systems

If you use a sound bar or receiver connected via HDMI ARC/eARC, Xiaomi TVs support eARC only on the port HDMI 1 (model 2021 year-end).

To output sound from the console directly to the sound system:

1. Connect the console to the port HDMI 2/3 (video).
2. Connect the sound panel to HDMI 1 (eARC).
3. In the TV settings (Settings) → Sound. → Digital audio output select Auto (Passthrough).
4. On the console (PS5: Settings → Sound. → Exit → Install a digital output, install Dolby Digital or PCM.

If the sound is coming through the TV (without an external system), check:

• 🔊 Nana PS5 In Settings → Sound. → TV or speaker output selected HDMI.
• 🔊 Xiaomi. TV In Settings → Sound. → Dolby Atmos Disabled (unless Support is available).
• 🔊 Volume level on Xiaomi remote is not set to a minimum (Volume button - could be pinched).

5. Solving common problems

Even after the right connection, errors can occur, and let's look at typical scenarios and how to fix them:

🖥️ Black screen after connection

• 🔌 Check the cable on another device (such as a laptop).
• 🔄 Restart the console in safe mode (for PS5: Hold the power button for 7 seconds).
• 📺 On Xiaomi TVs, reset the settings HDMI: Settings → Connections → Reset HDMI.
• 🔧 If you are using Nintendo Switch, upgrade the docking station (this is a problem for early revisions).

🎮 Delayed input (input lag)

• 🎯 Enable Game Mode on TV (Settings) → Picture → Image mode → Playing).
• 🔄 Turn off post-processing: Settings → Picture → Additionally. → Noise suppression → Off.
• 🖥️ Nana PS5 turn off VRR, If the TV does not support it (may add a delay).
• 📶 Make sure there are no interference sources nearby (e.g., a running microwave or router at 2.4 Hz).

🔊 No sound through HDMI

• 🔇 Check if the audio on the Xiaomi remote is turned off (Mute button).
• 🔊 In the setup of the consoles (PS5: Settings → Sound. → Exit, select HDMI instead of Controller.
• 🔧 On TV, reset the sound settings: Settings → Sound. → Sound reset.
• 🎵 If you are using Dolby Atmos, try switching to Dolby Atmos. PCM (Not all Xiaomi models support Atmos through the HDMI).

💡

If Xiaomi TV doesn’t recognize PS5 into 4K@120Hz, Update the TV firmware to the latest version. → On TV. → Update the software check the relevance of the.

6. Additional settings to improve gameplay

To maximize the potential of the game console Xiaomi TV, tune in:

🎨 Image quality

• 🖼️ Brightness/Contrast: Set Brightness to 50-60%, Contrast to 80-90% (for the first time) HDR These parameters are blocked).
• 🎭 Color Temperature: Choose Standard or Warm (cold tones tire your eyes).
• 🔍 Sharpness: Reduce to 20–30% – High values add artifacts.
• 🌈 HDR: Nana PS5 In Settings → Screen and video → HDR calibrate the brightness according to the instructions on the screen.

⚡ Productivity

• 🔋 On Xbox Series X, turn on Power Saving Mode (Settings) → General. → Power supply parameters – this will reduce heating.
• 🖥️ Nana PS5 Turn off the gameplay recording (Settings) → Capture and broadcast, if you don't use it, it frees up resources.
• 📦 For Nintendo Switch, use the original power supply in the dock – non-original can limit performance.

On Xiaomi TVs with Android TV (Like Mi. TV Q1E) You can activate the game launcher for quick access to settings:

1. Hold the Home button on the remote.
2. Select Games from the top menu.
3. Add a shortcut to Game Mode or Settings HDMI.

7. Features for older Xiaomi models TV

If your TV is released before 2020 years (e.g. Mi) TV 4S 55" or Mi TV 4A), It may not support HDMI 2.1 and 4K@120Hz. In this case:

• 📺 For PS5 Xbox Series X: Limit the resolution to 4K@60Hz or 1080p@120Hz.
• 🔌 Use the port. HDMI 3 – It often takes priority for gaming devices.
• 🔄 Disable Dolby Vision in the settings of the consoles – old Xiaomi models incorrectly handle this format.
• 🎮 If the input delay exceeds 30 ms, connect the console through HDMI-buffer splitter (e.g, OSSC), But it'll add a delay of 1-2 frames.

For models without ALLM (Like Mi. TV 4X) manually disable post-processing:

Settings → Picture → Additional →


- Noise suppression: Off.




- Motion improvement: Off.




- Dynamic contrast: Off.

8.Firmware Update: Why It Matters

The manufacturer regularly releases updates for Xiaomi TVs, fixing problems with the company. HDMI 2.1, VRR And it's also compatible with consoles. V2.0.163 for Mi TV Q2 Fixed error with flashing screen when connecting PS5 into 4K@120Hz.

How to update firmware:

1. Connect your TV to the Internet (via Wi-Fi or cable).
2. Go to Settings → About TV → Software Update.
3. Click Check Updates and install the latest version.
4. After the update, reset the settings. HDMI: Settings → Connections → Reset HDMI.

If the automatic update does not work:

• 📥 Download the firmware from the official Xiaomi website (the support section of your model).
• 📁 Copy the.zip file to a flash drive (format) FAT32).
• 🔌 Put the flash drive in. USB-port of the TV and update manually through Settings → On TV. → Update of the PO → Local Update.

💡

After updating the firmware of the Xiaomi TV reset the settings HDMI-CEC (Settings → Connections → HDMI-CEC → Reset) to avoid conflicts with consoles.

FAQ: Frequent questions