Setup digital TV on Xiaomi TV: full instruction with pictures

Xiaomi’s digital TV sets offer access to dozens of free channels in high quality, but many users have difficulty setting up their first setup. Unlike the old “stupid” TVs, where it was enough to connect the antenna and press “Autopoisk”, smart TVs Mi TV Redmi Smart TV They require the right signal source, broadcast format, and sometimes even manual input, and this article will help you understand everything from connecting an antenna to solving typical errors like "No signal" or "No services".

We will look at three main ways of setting up: etheric DVB-T2 (via room- or street-panel), IPTV (via Internet service provider and satellite TV (for models with DVB-S2 Special attention will be paid to models Xiaomi Mi TV P1, Redmi Smart TV X and Mi TV Q2, Because they're different from the older versions, if your TV doesn't catch channels after you search automatically, there's a section in the article that looks at the reasons and solutions Step-by-step.

Before you start setting up, make sure your Xiaomi TV supports the desired broadcast format.All current models (released after 2020) are tuners-ready. DVB-T2 for on-air television and DVB-C Satellite tuner for cable. DVB-S2 It is less common - it can be found in the flagship series of the Mi type. TV Master or Mi TV QLED. You can check the availability of the tuner in the technical specifications on the official website or in the Settings menu. → On TV. → Technical data.

1. Xiaomi TV Preparation for Digital TV Setup

Before you start searching for channels, you need to connect the equipment correctly and select the source of the signal, which is often missed, which causes the TV to not see the antenna or show a "No signal" error.

• 📡 Connect the antenna to the connector. RF IN (or ANTENNA IN) For room antennas, use an extension cord if the cable is not reaching.
• 🔌 Check the power: if you have an active antenna with an amplifier, connect it to the socket through the power supply (usually comes with a kit).
• 📶 Select the source of the signal: on the remote, click the Source (or Input) button and select TV (or Antenna).
• 🔄 Update your firmware: Outdated software may not support new broadcast standards. → On TV. → Updating the system.

If you're setting up IPTV (TV over the Internet, instead of an antenna, you will need to connect the TV to the network via Wi-Fi or Ethernet cable. → Network and Internet and select your connection. Internet speed must be at least 15 Mbps for stable browsing HD-You can check the speed through the built-in Speedtest app (available in Mi). TV App Store).

⚠️ Note: On Xiaomi TVs with Google operating system TV (2023-2026 models) TV settings may differ: If you do not have an antenna in the signal sources, update the firmware or use an external tuner.

2. Set up digital TV broadcasting (DVB-T2) Xiaomi

Television on air DVB-T2 — The most common way to view free 20–30 In Russia, two multiplexes (channel packets) are used for broadcasting: RTRS-1 (Channel One, Russia-1, Match TV and RTRS-2 (NTV, TNT, REN TV, to catch them, follow these steps:

1. On the remote, press the Home button, then go to Settings. → Channels → Tune in TV.
2. Choose the Etheric TV (DVB-T) or Digital TV (DVB-T2) — model-wise.
3. Click AutoSearch and select the country of Russia (or your region if the TV supports local settings).
4. Specify search type: Digital channels (do not select Analog channels, as they are disabled in most regions).
5. Run the search and wait until it's done. It can take 5 to 15 minutes.

If you find fewer than 20 channels after autosearch or one of the multiplexes is missing, try manually configuring:

• 📍 In the TV settings menu, select Manual Search.
• 📶 Specify the frequency for your region (for example, for Moscow it is 546 MHz and 498 MHz.
• 🔍 Run a search at the selected frequency. If the signal is weak, try turning the antenna or moving it closer to the window.

Connected antenna to connector RF IN|

Selected the correct signal source (TV)/Antenna)|

The TV is updated to the latest firmware|

In the search settings selected country "Russia"|

Search for only digital channels (DVB-T2)-->

If the TV doesn’t find channels even after manual tuning, the problem may be:

💡

If Xiaomi TV doesn't catch DVB-T2, Try resetting TV settings to factory: Settings → Channels → Reset TV settings. Repeat auto search after reset.

3. Connection and setup IPTV Xiaomi TV

IPTV — This is Internet-based television, which is offered by many providers (Rostelecom, MTS, Beeline), the advantage of this method is a stable signal and access to additional channels, but you need to connect to the network at a speed of 20 Mbps. On Xiaomi TVs there are two ways to configure the system. IPTV:

Method 1: Through the built-in application "IPTV"

Many Mi models TV Redmi Smart TV have a pre-installed application IPTV (live TV). To set it up:

1. Open the app. IPTV main menu.
2. Select Add Playlist and enter data from the provider (usually this is a link to the.m3u login).
3. If the provider requires MAC-Address, find it in Settings → On TV. → Network status.
4. Save the settings and wait for the list of channels to load.

Method 2: Through third-party applications (SS IPTV, Lazy IPTV)

If the built-in app is not suitable, install an alternative from Mi. TV App Store:

• 📺 SS IPTV — playlist-support.m3u and EPG (transmission).
• 🎯 Lazy IPTV — convenient interface with the ability to sort channels.
• 🔗 OTT Player – often used by providers for login/password authorization.

For installation:

1. Open Mi. TV App Store and find the right app.
2. Set it up and open it.
3. Enter the data from the provider (link to the playlist or authorization data).
4. Restart the TV if the channels don’t appear immediately.

⚠️ Note: Some providers block access to the IPTV If the channels are not working, contact the provider’s technical support and check if you are allowed to use Xiaomi. TV viewable.

4. Satellite TV setup (DVB-S2) on Xiaomi

Satellite TV is only available on Xiaomi TVs with tuner DVB-S2. These are flagship models of the Mi type. TV Master, Mi TV QLED 75" or "Redmi Smart" TV MAX 98.” Adjustment will require:

• 🛰️ Satellite antenna (plate) with converter (LNB).
• 📡 DiSEqC switch (if you connect several plates).
• 🔌 Cable with an F connector for connecting to a TV.

Step-by-step:

1. Connect the cable from the satellite antenna to the connector LNB IN TV-wise.
2. Go to Settings → Channels → TV setup → Satellite TV (DVB-S2).
3. Select Add Satellite and name it (e.g. Yamal 402, Eutelsat) 36B or ABS-2 for Tricolor TV).
4. Enter the transponder parameters (frequency, symbolic speed, polarization) and for popular satellites, this data can be found on the ISP websites.
5. If you find few channels, check DiSEqC settings (if you use a switch).

To view paid packages (for example, Tricolor TV or NTV-Plus) will be required CAM-module and smart card. Put the module in the connector. CI+ on TV, and the map on the CAM-Then start searching for the channels again.

1. Correct cable connection (no breaks, connectors tightly twisted).

2. antenna direction (the dish must be precisely oriented to the satellite).

Transponder parameters (frequency, symbolic speed, FEC).

4. Power supply on the converter (if active is used) LNB).-->

5. Solving Digital TV Problems on Xiaomi

If the channels don't show you, after setting up, whether the image is getting stuck or not, use this troubleshooting manual.-5 errors and ways of correcting them:

If your Xiaomi TV is constantly resetting your channel settings after you turn off, activate the Quick Start feature:

1. Go to Settings. → Power and screen.
2. Enable the Quick Start option.
3. Turn off the energy saving if it is active.

Important: On Xiaomi TVs with firmware MIUI TV 3.0 and later, when reset to factory settings, all saved channels are also reset. To avoid this, export the list of channels to the file before reset: Settings → Channels → Channel management → Exports.

6. Optimization of image and sound for digital TV

Once you've successfully set up channels, you should adjust the picture and sound for maximum comfort. 1080i or 720p, Therefore, it is important to choose the right display modes.

Image setting

• 🎨 Picture Mode: Select Movie or Standard in Settings → Display and sound → Image mode.
• 🔍 Sharpness: Reduce to 30-40% to reduce noise on low bitrate channels.
• 🌈 Color Temperature: Set Warm for more natural skin tones.

Sound tuning

• 🔊 Sound mode: Select Speech for News or Movie for Movies.
• 🎛️ Equator: Increase the average frequencies (500–2,000 Hz) for better readability.
• 🔇 Volume normalization: Turn on to remove sudden changes in sound between channels.

If the image is “breaking” or artifacts are observed, try changing the signal format:

1. Go to Settings. → Display and sound → Additional settings.
2. Select the format HDMI (Even if you use an antenna).
3. Install. 1080p 50 Hz is the optimal mode for digital TV in Russia.

7. Alternative ways to watch TV on Xiaomi

If the built-in TV features are not satisfied, you can use external devices or applications for watching TV:

• 📦 Prefix (TV box): Connect Xiaomi Mi Box S or NVIDIA Shield through HDMI and use apps like Peers.TV or Wink.
• 🖥️ Transcoding: Set up a home server with Plex or Jellyfin and stream TV to your TV.
• 🌍 Web-TV: Open your browser on your TV and go to sites like tvzavr.ru or tvonline.ru (requires a stable Internet connection).

For models without built-in tuner (for example, Xiaomi Mi) TV 4A Early versions of the TV show, the only way to watch TV is to use external TV. DVB-T2 Connect it to the TV through the tuner. USB or HDMI and install the appropriate application (for example, DVB-T2 Player from Mi TV App Store).

💡

If you use Xiaomi Mi Box to watch TV, install the app TVIR — It supports playlists. IPTV and comfortable EPG (transmission).

Frequently Asked Questions (FAQ)