How to set up a Xiaomi Mi TV 4A: a complete guide from connectivity to smart features

Xiaomi Mi TVs TV 4A They gained popularity due to the combination of affordable prices, high quality 4K-screen and smart functions based on Android TV. But even this simple device requires the right initial setup to unlock its full potential, and many users face challenges when connecting to Wi-Fi, setting up digital channels, or activating a voice assistant. This article will help you avoid typical mistakes and customize Xiaomi TV 4A efficiently.

We're going to look at not only the basic steps, from unpacking to first switching on, but also the advanced settings: optimizing the image for different signal sources, integrating with the Mi Home ecosystem, and solving common problems. We'll focus on adjusting the audio through HDMI ARC and updating the firmware, as these are often questions, and if you just purchased the Mi TV 4A 32, 43" or 50" this will be your guide to all the stages of the setup.

Preparation for the first inclusion: unpacking and connection

Before you start setting up, it is important to properly prepare the TV and workspace. Start by unpacking: carefully remove the Xiaomi Mi TV 4A from the box, removing the protective film from the screen (it can be almost invisible!). Make sure that the kit includes a Bluetooth remote (with the Mi button), a power supply, an HDMI cable and an instruction. If you bought a model with a stand, check for mounting screws.

The choice of location for the TV depends on its diagonal:

• 📏 32-inch model: optimal viewing distance 1.2-1.6 m
• 📺 43-50 inches: Place at 1.8-2.5 m distance
• 🔌 The socket should be close by - the power cable on the Mi TV 4A is not too long (1.5 m)
• 📡 Wi-Fi router: If you plan to stream in 4K, place your TV in a confident signal zone.

⚠️ Warning: Do not install the TV in niches with poor ventilation. Xiaomi Mi TV 4A has passive cooling, and overheating can lead to automatic shutdowns during prolonged use.

Connect the cables in this sequence:

1. Connect the power supply to the TV and outlet.
2. Connect the antenna cable (if you plan to watch TV).
3. Insert HDMI- devices (set-top box, game console) in the ports HDMI 1/2/3 (port HDMI ARC is needed for sound systems).
4. If you use headphones over Bluetooth, you can connect them later through the settings menu.

First Including and Selecting System Language

Once power is on, press the Power button on the remote (or on the back of the TV) and it takes up to 30 seconds for the first time to turn on the Mi logo. Then the system will suggest selecting the interface language.

• 🌍 Russian is available in firmware for the CIS market. If it is not available, you will have to update the software (instruction below).
• 🔄 Reset to factory settings (via Settings → Device → Reset) will return this screen if you made the wrong choice.

Once you have selected the language, the system will suggest connecting to the network. Here's a nuance: if you're using a hidden Wi-Fi network, first press Other Networks, then type the name (SSID) manually. For wired connection (recommended for 4K- streaming), use the Ethernet port on the back.

💡

If your TV doesn’t find your Wi-Fi network, try temporarily disabling 802.11r (Fast Roaming) mode on your router – it can conflict with Android TV.

In the next step, the system will prompt you to log into a Google or Mi Account, which is optional, but gives you access to:

• 🎬 Google PlayFilms and other services
• 🔄 Synchronization of installed applications
• 🔐 Remote control capabilities via Mi Home

If there is no account, select Skip (you can add it later to Settings → Accounts).

Configuring digital and air channels

One of the key stages is the search for TV channels. Xiaomi Mi TV 4A has two options: digital TV (DVB-T2) and analog. For most regions of Russia and the CIS, digital broadcasting is relevant (20 channels in the first multiplex, 10 in the second).

1. Go to Settings → Channels → Set up TV.
2. Select Digital Channels (DVB-T2).
3. Specify the region (for example, Moscow or St. Petersburg).
4. Start AutoSearch - the process will take 3-5 minutes.

If no channels are found:

• 📶 Check signal quality in the Manual Setup menu (level must be >70%).
• 🔄 Try another signal source (e.g., a collective antenna instead of a room antenna).
• 📡 In rural areas, a signal amplifier may be required.

⚠️ Warning: Once channels are searched, you can change the order of channels in the Channel Management menu, but changes will reset after the firmware update, which is a bug that is present in some versions of the Mi TV 4A software.

For analog TV, select Analog Channels and search, but note that since 2026, analog broadcasting has been disabled in most regions, and this mode is only needed for retro devices (for example, VCRs).

Optimization of image and sound

Xiaomi Mi TV 4A supports 3840×2160 (4K) resolution, but by default, it often uses settings that are not optimal for your content.

1. Go to Settings → Display and sound → Picture.
2. Select Movie for Movie or Game for Consoles (reduces input delay).
3. Turn off Dynamic Contrast, which artificially inflates the brightness in dark scenes.
4. Enable HDR if your content supports it (only available on HDR10 models).

For sound, the key settings are in Settings → Display and Sound → Sound:

• 🎵 Sound mode: Standard for movies, Music for concerts.
• 🔊 Equalizer: Increase low frequencies for bass or high frequencies for clarity of speech.
• 🎧 Bluetooth audio: If you connect headphones, select the AAC codec for the best quality.

If you use a sound bar or receiver, connect them via the HDMI ARC port and enable this feature in the Settings menu → Display and Sound → Digital Sound (HDMI) This will allow you to transfer sound from the TV to the speaker system without additional cables.

Internet connection and setting up smart functions

Xiaomi Mi TV 4A runs on Android TV, which allows you to access thousands of apps through Google Play, but you need a stable Internet connection to install them.

• 📶 Check if your router supports 802.11ac (5GHz) standard. Mi TV 4A runs faster on that network.
• 🔌 For 4K- content (Netflix, YouTube), it is better to use a wired connection.
• 🔄 If the TV is frequently turned off from Wi-Fi, turn off Band Steering in the router settings.

After connecting to the network, we recommend installing the following apps (available on Google Play):

• 🎬 Kodi is for local film playback.
• 🎵 Spotify is for listening to music.
• 🎮 Steam Link is a PC-based game streaming service.
• 📺 Peers.TV — to watch IPTV.

To control the TV from a smartphone:

1. Download the Mi Remote app (available for Android and iOS).
2. Connect your phone and TV to the same Wi-Fi network.
3. In the app, select the Mi TV 4A model and follow the instructions on the screen.

💡

To watch Netflix in 4K on Xiaomi Mi TV 4A, you need to upgrade to 2.0.69 or later and install the Netflix app from Google Play (not via APK).

Updating firmware and solving problems

Regular firmware updates fix bugs and add new features.To update the Xiaomi Mi TV 4A:

1. Go to Settings → About TV → System Update.
2. Click Check for updates.
3. If a new version is available, confirm installation. The TV will restart automatically.

If the update is not installed:

• 🔌 Check your internet connection (speed >5 Mbps required).
• 💾 Download the firmware manually from Xiaomi’s official website, save to a flash drive (FAT32) and update via Local Update.
• 🔄 If the TV is stuck on the logo after the update, reset (press Menu + Volume Down on the remote when you turn on).

⚠️ Warning: Do not turn off the TV during the upgrade (the indicator on the front will flash red).Aborting the process can lead to a device "brick" that is eliminated only through service mode.

Common problems and their solutions:

Integration with Xiaomi (Mi Home)

Xiaomi Mi TV 4A can become a smart home control center if you have other Mi Ecosystem devices (lamps, sockets, robot vacuum cleaner).

1. Install the Mi Home app on your smartphone.
2. Add the TV to the app via Add the device → TVs.
3. Confirm the pairing on the TV screen.

After you connect, you can:

• 🎤 Control your TV with your voice through Alice or Google Assistant.
• 🔄 Automate scripting (e.g., turn off TV when you activate Sleep mode).
• 📱 Use the TV as a control panel for other devices (e.g., turn on the Yeelight lamp from the remote).

For voice control:

1. Press the microphone button on the remote.
2. Say a command such as “turn on Channel One” or “turn up the volume by 20%.”
3. To work with Alice, install the Yandex app from Google Play.

💡

If the voice assistant does not respond to commands, check the settings of the TV section Voice input → Recognition language – Russian (Russia) should be selected.

FAQ: Answers to Frequent Questions