How to set up channels on a Xiaomi TV: a complete guide with photos and videos

Setting up channels on a Xiaomi TV is a process that seems complicated at first glance. In fact, the Mi TV and Redmi Smart TV interface are designed so that even a beginner can sort it out without assistance. However, there are nuances ranging from choosing the right signal source (antenna, cable, satellite) to the subtleties of manually tuning for a weak signal. In this article, we will examine all the ways from automatic search to solving typical problems when the TV “can’t see” channels or shows them with interference.

It's important to understand that the setup algorithm depends on the TV model and the firmware version. For example, in Xiaomi Mi TV 6, the menu is different from the Redmi Smart TV X50, and the updates from 2023-2026 made changes to the Settings → Channels section. We took into account all the current versions of the software and collected universal instructions that will suit most of the brand's devices. If your TV is released before 2020, some menu items may be called differently - we will mention this too.

1. Preparation of the TV for channel settings

Before you start searching for channels, make sure that the TV is properly connected to the source of the signal, which depends on whether it finds at least one channel or produces an error No signal.

Here's what you need to check:

• 📡 Antenna: if you use on-air or digital TV (DVB-T2), The antenna must be connected to the connector ANT IN For indoor antennas, select a place with minimal interference (for example, not near the microwave oven).
• 📺 Cable TV: if you have an operator (Rostelecom, MTS, Tricolor), connect the cable to the connector CABLE IN or RF IN. Check with the provider if you need it. CAM-decoding-module.
• 🛰️ Satellite TV: Tricolor, NTV-Plus or other operators will require a receiver (unless the TV supports built-in TV). DVB-S2). Connect it through. HDMI or AV.
• 🔌 Power: Make sure the TV is plugged in without adapters – power surges can knock down settings.

If you connect via a set-top box (e.g. for satellite TV), set it up first, then select the appropriate signal source on the TV (typically HDMI 1/2), in which case the channel settings will take place on the console, not on the Xiaomi menu.

⚠️ Warning: If you use an active antenna (amp), connect its power supply to the outlet. Without power, the signal will be too weak, and the TV will not find channels even under ideal conditions.

2. Automatic channel search on Xiaomi TV

This is the easiest way, which is 90% of the time: the TV will identify the channels available and store them in memory, and the instructions are relevant for the Mi TV 4A/4S/5/6 and Redmi Smart TV models with firmware in 2022 and later.

Steps for automatic setting:

1. Turn on the TV and press the Menu (or Settings) button on the remote.
2. Go to Settings → Channels → AutoSearch (in some models, the path may be Settings → Broadcast → AutoSetting).
3. Select the source of the signal: 📶 antenna (DVB-T/T2) — digital-only. 📡 Cable (DVB-C) — for cable television from the operator.

Russia

Finland

OK.

Once completed, the TV will show the number of channels found, and you can sort them by number or name in Channel Management.

⚠️ Warning: If the TV finds channels but they don't show (black screen or no signal), check if you have a digital TV service activated from the operator. For example, Rostelecom may require the TV to be tied to the personal account.

Manual Channel Customization (for Power Users)

Autosearch doesn't always do the job -- especially if the signal is weak or you want to add a specific channel that the TV doesn't see. In this case, manual tuning will help. It's also useful if you know the exact parameters of the broadcast (frequency, symbolic speed, etc.).

How to set up channels manually:

1. Go to Settings → Channels → Manual search.
2. Select the signal type: DVB-T2 (Etheric), DVB-C (Cable) or DVB-S2 (Satellite if supported).
3. Enter the parameters: 📡 Frequency (MHz): For example, for the First Multiplex in Moscow, it is 546 MHz. 🔄 Symbolic speed: for DVB-T2 usually 6875. 🔢 Modulation: 256 QAM (for cable TV) or COFDM (airy).

Search

If you don’t know the parameters, you can find them on the RTRS website (enter your region) or check with the cable operator. For satellite TV (for example, Tricolor), the parameters are usually specified in the contract.

💡

If the TV doesn’t save channels after manually setting up, try resetting the list of channels to factory settings in Settings → Channels → Reset.

Satellite channel configuration (DVB-S2)

Not all Xiaomi TVs support built-in DVB-S2 (satellite tuner). For example, Mi TV 4A does not, but Mi TV 6 may. To see if your model supports satellite TV, check the specs on Xiaomi's website or look at the connectors on the back - there must be an LNB IN port.

If you have support, here’s how to set up satellite channels:

1. Connect the cable from the satellite antenna to the LNB IN connector.
2. Go to Settings → Channels → Satellite settings.
3. Select a satellite (e.g. Eutelsat 36A/36B for Tricolor or ABS-2 for NTV-Plus).

⚠️ Warning: If all channels are missing after the firmware update, don't panic, that's standard. Just run the autosearch again, and the TV will restore the list.

Sorting and management of channels

Once you've set up channels, you can sort them out, delete them, or add them to favorites, which is convenient if the TV has found a lot of garbage canals or they're in a chaotic order.

How to manage channels:

1. Go to Settings → Channels → Channel Management.
2. Select a channel and press OK on the remote to open the action menu: 🔄 Move: Change the order of channels with the Up/Down buttons. 🗑️ Delete: removes the channel from the list (can be restored by auto search). ⭐ Add to your favorites: the channel will appear in a separate list. 🔒 Block: Protection from children (required) PIN).

Exit

Back up.

If you need to hide adult channels, activate parental controls:

1. Go to Settings → Security → Parental Controls.
2. Install. PIN-code (default frequency 0000 or 1234).
3. Choose channels to block or set age limits.

How to install the application:

1. Click the Apps button on the remote or go to Settings → Applications.
2. Select Install from USB (if you downloaded APK) or find the app in the App Store.
3. After installation, open the application and log in to the operator account (if required).

The advantage of this method is that you don't have to manually configure channels, you just need to log in, but you will need high-speed Internet (from 20 Mbps for Full HD) to work reliably.

8. firmware update for better TV performance

If the TV is not catching channels well or settings are often confused, the reason could be outdated firmware. Xiaomi regularly releases updates that improve tuner stability and add support for new broadcast standards.

How to update firmware:

1. Go to Settings → About TV → System Update.
2. Click Check for updates.
3. If a new version is available, confirm the installation.

If the TV does not find updates via the Internet, download the firmware manually:

1. Find the latest version for your model on the Xiaomi Firmware Updater website.
2. Download the file and save it to a flash drive in FAT32 format.
3. Connect the flash drive to the TV and select Update via USB.

⚠️ Warning: Don't turn off the TV during the upgrade! If the process stops, the device may stop turning on.

💡

Updating your firmware can solve channel search problems, especially if your model is released before 2022. New versions of the software often add support for modern broadcast standards (for example, DVB-T2 HEVC).

FAQ: Frequent questions about setting up channels on Xiaomi TV