How to set up a remote on a TV Xiaomi: the complete guide

Integration of equipment from the provider with modern smart technology often raises questions among users, especially when it comes to consolidation of control. Owners of Xiaomi Mi TVs and consoles often face the desire to control the entire multimedia system with one device, without switching between several remotes. The setting of the remote by Rostelecom on Xiaomi equipment is possible thanks to the support of HDMI-CEC standard or through programming of IR codes, which greatly simplifies interaction with the interface.

The synchronization process depends on the specific model of your Wink or RT console, as well as the version of the Android TV operating system installed on the TV or Mi Box. In some cases, it is enough to activate one function in the menu, in others you will need to manually calibrate the buttons through the hidden remote menu. Understanding the principles of the infrared port and the HDMI-CEC protocol will help avoid typical errors when pairing devices.

In this guide, we will take a look at all the connectivity methods available, from automatic settings to manual code entry, how to make the volume and on buttons work correctly, and what to do if standard methods fail, and the right configuration will make your equipment set into a single ecosystem with easy management.

Preparatory stage and compatibility check

Before you start the active setup phase, you need to make sure that your equipment is technically ready for synchronization.Most modern Xiaomi TVs with a diagonal of 32 inches and the Mi Box S consoles support the protocol for managing consumer electronics. However, older remote models by Rostelecom released more than 5 years ago may not have the function of programming the TV code.

Carefully inspect the remote control from your console. The front panel or under the battery compartment cover should have a model marking, for example, RT-RS-28 or Wink One. For voice-controlled models, the process is often simplified with a Bluetooth connection, while classic IR remotes require accurate access to the code spectrum.

It is also important to check the status of the batteries, as the programming process can take several minutes, and a weak charge can interrupt the signal transmission. Make sure there are no physical obstacles between the Xiaomi TV receiver and the remote transmitter if you use the infrared method. For Bluetooth models, the distance is not critical, but the proximity of the devices will speed up the detection process.

⚠️ Note: Do not try to program the remote if the console Rostelecom is in deep sleep or is off the outlet - for some models this is a prerequisite for entering programming mode.

Automatic configuration via HDMI-CEC

The most modern and convenient way to control a Xiaomi TV with a Rostelecom remote is to use HDMI-CEC technology, which allows you to transmit control commands over an HDMI cable, which eliminates the need to “train” the remote with infrared signals. If your console is connected to the TV via HDMI, this method is a priority.

To activate the feature, you need to go to the settings of the Xiaomi TV itself. The interface may vary slightly depending on the version of the PatchWall shell or pure Android TV, but the logic remains the same. You need to find the section responsible for external devices or general system settings where the control of the CEC is hidden.

Once the function is activated on the TV, Rostelecom’s console must automatically gain control of the basic functions of turning on, off and adjusting volume, and in some cases, both devices need to be rebooted to apply the changes. If the automatic determination does not work, check if it sits tightly. HDMI-plug-in.

💡

Use quality. HDMI-2.0 or higher cable with support ARC, to ensure stable transmission of control signals between the set-top box and the TV.

The table below gives the names of the HDMI-CEC feature for various manufacturers that may be found in the menu of your Xiaomi TV or in the set-top box settings:

Manual programming of TV IR codes

If CEC technology is not supported or is not running smoothly, the only solution is manually programming the remote’s infrared port by Rostelecom, which requires you to enter a special digital code corresponding to the brand of your Xiaomi TV.

Most modern Wink and RT consoles use a combination of OK and TV (or Power) buttons, which require you to hold these two buttons simultaneously and hold them for 3-5 seconds until the light flashes twice, which puts the remote into the TV code learning mode.

Once you enter programming mode, you need to enter a four-digit brand code. Xiaomi TVs are often suitable for codes intended for other Chinese manufacturers such as Haier, TCL or Hisense, as they use similar IR signal matrix. Once the code is entered, the indicator should flash, confirming the acceptance of the command.

It's important to check each button after you enter the code, and if the volume buttons are working and the power button is not, then the code is partially matched, and then you should try the next code from the compatibility list, and the process may take time, but it's worth it for comfortable use.

Configure through the application "My Rostelecom"

Owners of new voice-controlled consoles can make it much easier to do so using the official My Rostelecom (or Wink) mobile app, which avoids tambourine dancing around IR ports and manual code entry, a technique that is especially relevant for users who don’t want to understand technical nuances.

First, make sure your smartphone and Rostelecom are connected to the same Wi-Fi network. Run the app on your phone and go to the device management section. The system will automatically detect your console and suggest setting up the remote. During the setup process, the app will ask for your TV model — select Xiaomi from the list.

The app will take you through several test steps, checking the TV's response to commands. If the TV responds correctly, the settings are stored in the cloud and automatically applied to your remote, thanks to the fact that modern Rostelecom remotes have their own Wi-Fi or Bluetooth module to communicate with the configuration server.

Troubleshooting and troubleshooting

Even if all instructions are followed, there can be situations where the remote is behaving incorrectly, such as buttons that are delayed, or the TV can turn off spontaneously, often the problem lies in the conflict of signals, when the infrared port of the TV and the command from the console via HDMI are simultaneously working.

If you see a "double" command (the TV responds twice to a single press), try turning off HDMI-CEC control in the TV settings, leaving only IR control, or vice versa. It is also worth checking whether the IR receiver is blocked by the sound bar or other accessories installed next to the Mi logo.

In cases where the remote stops responding after setting up, perform a complete reset of the remote, which usually requires removing the batteries, clamping all the buttons for 10 seconds, and then inserting the batteries back and repeating the programming procedure, which clears the device's internal memory of erroneous configurations.

⚠️ Note: When resetting the remote settings, all previously saved macros and custom button settings will be removed without recovery, so make sure you really need a full reset.

Use of universal codes and alternatives

If the standard codes for Xiaomi don't work, you can use universal codes for the group "DTV" or "LCD TV." Rostelecom remotes have an extensive database, and often code from a less popular brand is compatible with your TV. Experiments with codes from BBK or Dexp sometimes give an unexpected positive result.

Alternatively, you can use the Learn feature if your Rostelecom remote supports this technology, and you need a second, native remote from a Xiaomi TV, you put the remote by Rostelecom into training mode, you bring two face-to-face remotes 2-3 cm away, and you transmit button signals.

This method guarantees 100% compatibility, because the remote simply copies the signal without trying to interpret it, but it requires a working native remote and a little more time to set each button separately, but you can program even those buttons that are not in the standard set, such as a quick call to applications.

💡

Direct learning (copying) is the most reliable way to set up if the automatic codes don’t work, but requires a second, serviceable remote.

Frequently Asked Questions (FAQ)