How to set up the remote from the TV Xiaomi: full instructions with photos and tips

Xiaomi’s remote control from TVs is not just a button to switch channels, but a smart device with advanced features. However, even such an advanced gadget can cause difficulties: it does not sync with the TV, does not respond to presses or works with delay. In this article, we will discuss all the ways to set up the Xiaomi TV remote, from basic synchronization to solving non-standard problems.

Whether you’ve bought a new Mi TV 4S, Redmi Smart TV or Xiaomi TV Q2>, the remote settings are universal for most models. We’ll also tell you how to update the remote’s firmware, replace the batteries, and what to do if the device stops answering. At the end of the article, we’ll give you answers to frequent questions and life hacks that will save you time.

1.Preparation for setting up the Xiaomi TV remote

Before you start synchronizing, make sure that the basic conditions are met. Often, the remote problems are not due to a malfunction, but to trivial omissions.

First, check the power supply. Even if the display on the remote flashes, the batteries can be discharged. Use AAA alkaline cells (Duracell or Energizer are recommended) - they hold the charge longer. Second, remove the protective film from the infrared (IR) emitter if the remote is new. It can block the signal.

• 📱 Bluetooth: If the remote supports Bluetooth (voice-controlled models), turn this feature on in your TV settings.

Important: Xiaomi’s latest-generation remotes (e.g., the Xiaomi TV Q2 75) can use both IR and Bluetooth. If synchronization doesn’t work, try both.

2. Basic synchronization of the remote with the TV

If the remote is new or has been reset, it must be paired with the TV, taking no more than 2 minutes, but requires precise steps.

For IR remotes (most Mi TV and Redmi TV models):

1. Turn on the TV with the power button on the body.
2. Point the remote to the IR receiver of the TV (usually from the bottom down the center).
3. Press the Menu + OK buttons for 5-7 seconds at the same time until the indicator blinks twice.
4. Press Power – the TV must turn off and turn on again.

For Bluetooth remotes (such as voice control):

1. Go to Settings → Devices → Bluetooth.
2. Activate device search.
3. Press Mi + OK on the remote until the indicator flashes.
4. Select the remote from the list of found devices and confirm pairing.

Remote responds to pressing (menu opens)

The indicator on the remote flashes when you press the buttons

The TV is turned off/on by the Power button

The voice assistant (if any) is activated by the Mi button.-->

If the sync fails, try resetting the remote to the factory settings. To do this, remove the batteries, press any button for 10 seconds, then insert the batteries back and repeat the pairing procedure.

3. Configure additional remote functions

Modern Xiaomi remotes support not only basic commands, but also advanced functions: voice control, gestures, smart home control. Let's see how to activate them.

Voice assistant

If your remote is equipped with a microphone (Mi button with microphone icon), connect it to Google Assistant or XiaoAI:

1. Hold the Mi button for 2-3 seconds until a hint appears on the screen.
2. Follow the instructions for logging in to your Xiaomi or Google account.
3. Set up the language (Russian, English, Chinese available).

Gesture management

Some remotes (such as the Xiaomi TV Q1E) support gestures to adjust volume or scroll through menus.

1. Go to Settings → Remote DU → Gestures.
2. Activate the option and test the movements (up/down for volume, left/right for rewind).

Warning: If the voice assistant doesn't recognize commands, check the TV's Internet connection. The feature requires a stable connection to handle queries on Xiaomi servers.

4. Battery replacement and remote care

The life of the batteries in the Xiaomi remote depends on the intensity of use and type of batteries. On average, AAA alkaline batteries last 6-12 months, and batteries last up to 2 years.

To replace the batteries:

1. Turn the remote and find the compartment cover (usually fixed by a latch).
2. Put the lid on a flat object (such as a coin) and remove it.
3. Remove old batteries by observing polarity (+ and −).
4. Insert new elements, making sure the contacts match.

💡

If the remote starts to "glutch" after replacing the batteries, remove them for 1 minute, then insert them back in. This will release the residual charge in the capacitors.

To extend the service life of the remote:

• 🧹 Cleaning: once every 3 months wipe the buttons with an alcohol napkin (without abundant moisturizing).
• 🚫 It is forbidden: to drop the remote, to expose to moisture or direct sunlight.
• 🔄 Storage: If you don’t use the remote for a long time, remove the batteries to avoid contact oxidation.

Warning: If the remote does not work after replacing the batteries, check the contacts in the compartment for corrosion. Clean them with a cotton swab dipped in vinegar, then dry them.

5. Solving the problems with the Xiaomi TV remote

If the remote has stopped responding to commands, is not synchronized or is working with interruptions, use this instruction.

The remote doesn't turn on the TV.

Causes and solutions:

• 🔌 No power: check batteries or connect the TV to the outlet (probably the protective mechanism worked).
• 📡 Interference: Turn off other IR devices (air conditioning, music center) – they can block the signal.
• 🔄 Reset remote: Remove the batteries for 5 minutes, then insert back and repeat synchronization.

Buttons are running with a delay

This is a typical problem for remotes with low battery charge or interference in the IR signal, and delays can also occur due to:

• 📶 Weak signal: Close the remote to the TV (maximum 3 meters).
• 🖥️ TV congestion: Close background applications in Settings → Annexes → Launched.
• 🔄 Software Update: Check the relevance of TV firmware in Settings → On TV. → Updating the system.

Critical information: If the Bluetooth remote stopped connecting after updating the TV firmware, reset the network. To do this, go to Settings → Network → Reset network settings and repeat pairing.

6. Update of Xiaomi remote firmware

The firmware of the remote is updated automatically with the TV, but sometimes manual installation is required.This can fix bugs with delays, broken buttons or sync problems.

To update the firmware:

1. Connect your TV to the Internet (preferably via Ethernet cable for stability).
2. Go to Settings → About TV → System Update.
3. If an update is available, confirm installation. The remote will update automatically.

For manual firmware (if the automatic update does not work):

1. Download the latest firmware version for your model from the official Xiaomi website.
2. Unpack the archive and copy the update.zip file to the flash drive (FAT32 format).
3. Connect the flash drive to the TV and select Settings → About TV → Update via USB.

💡

Update your firmware only through official sources. Using third-party files can result in a remote or TV lock.

Warning: If the remote has stopped working after the update, reset the TV to factory settings (Settings → About TV → Data Reset) This will return compatibility with the remote, but delete all user settings.

7. Alternative ways to control the TV

If the remote is broken or lost, you can control the Xiaomi TV in alternative ways.

Mi Remote appendix

The official Xiaomi app allows you to use your smartphone as a remote. Download it from Google Play or the App Store and follow the instructions:

1. Connect your phone and TV to the same Wi-Fi network.
2. Open the app and select Add Device → TV.
3. Follow the synchronization tips.

Universal remotes

If the original remote is lost, you can use a universal one (for example, Xiaomi Mi Universal Remote).

1. Turn on the TV with a button on the body.
2. On the universal remote, press the Setup until the indicator flashes.
3. Enter the code for Xiaomi TV (usually 0178 or 0031).
4. Check the buttons.

Voice assistants

Xiaomi TVs support control via Google Assistant or Alice (if connected to a smart home).

• “OK Google, turn on Xiaomi TV on Channel One.”
• "Alice, turn up the TV in the living room."

To do this, connect the TV to your Google or Yandex account and activate voice control in the smart home settings.

Frequent Questions (FAQ)