Set up channels on Xiaomi TV: from auto-search to manual addition

Xiaomi TVs are not only affordable Smart TVs with wide multimedia capabilities, but also devices that require the right setup to watch on-air, cable or satellite TV. Many users face problems when connecting for the first time: channels are not located, the image is slowing down, or there is no signal. In this article, we will discuss all the ways to configure channels on Mi TVs (A Pro, P1, Q2, S Pro, etc.), including unique MIUI TV 2026 firmware chips that simplify the process.

It is important to understand that the configuration algorithm depends on the type of signal: digital (DVB-T2), analog, cable (DVB-C) or satellite (DVB-S/S2). We will consider each option taking into account the features of the Xiaomi interface, and also give recommendations for eliminating typical errors - from the lack of sound to "hang" TV during the scanning phase. If you just bought a Mi TV or moved to another region where the broadcast frequencies have changed, this guide will help avoid contacting the service center.

Before you start, make sure you have everything you need:

• 📶 Antenna (room, street or collective) with a connected cable.
• ⚡ Signal source: terrestrial TV, cable operator or satellite dish.
• 🔌 Cable HDMI or AV (if you plug in the console).
• 📱 TV remote control (or Mi Remote app on your smartphone).

1. Preparing Xiaomi TV to set up channels

Before scanning channels, you have to do basic things that many people miss, and it's a waste of time, and that depends on whether the TV can find all the channels available and whether there's a stable signal.

First, check the physical connection:

• 🔌 Connect the antenna cable to the connector RF IN (or ANTENNA) Make sure the plug is screwed to the end, so that the weak contact can cause the signal to be lost.
• 🔄 If you use a signal amplifier, turn it on in advance (2-3 minutes before setting up).
• 📡 For satellite TV, check that the dish is aimed at the satellite (for example, Yamal 201 or the satellite). ABS-2 for Russia).

Second, update the firmware of the TV, and the old software may not support the new broadcasting standards.

1. Go to Settings → About TV → System Update.
2. Click Check Updates and wait for the process to complete.
3. If an update is found, install it and restart the device.

⚠️ Note: If the Xiaomi TV does not find updates via Wi-Fi, try connecting to the network via an Ethernet cable or download the firmware manually from the official Mi Support website (select your model). TV!).

Finally, reset the TV to factory settings if you've tried to set up channels before, but it didn't work, and this will clear the cache and eliminate any conflicts:

Settings → All settings → System → Reset settings → Reset TV settings

Antenna cable connection verified |

Updated TV firmware |

Resetting (if necessary) |

Connected to the Internet (for IPTV and updates)

-->

2. Automatic channel search on Xiaomi TV

The easiest way to do this is to use the autosearch function. Xiaomi TVs support scanning of both digital (DVB-T2) and analog channels.

1. Press the Menu button on the remote and select Settings → Television → Channel settings.

2. In the menu that opens, select AutoSearch and specify the signal type:

• 📶 On-air TV (DVB-T2) — Digital TV (20 free channels in Russia).
• 📺 Cable TV (DVB-C) — if connected to the operator (for example, Rostelecom or MTS).
• 🛰️ Satellite TV (DVB-S/S2) — dish-antenna.

3. Set up search parameters:

• 🔍 Full search – scans all available frequencies (recommended when you first connect).
• 🔄 Quick search – only checks popular frequencies (faster, but can skip channels).
• 📡 Manual frequency setting – if you know the exact frequency of multiplexes (e.g., multiplexes, 546 MHz for RTRS-1 Moscow).

4. Run the search with the OK button and wait until it's done. The process can take anywhere from 5 to 20 minutes depending on the number of channels.

⚠️ Note: If less than 10 channels are found after auto search, check: Quality of antenna cable (possible breaks or oxidation of contacts); antenna direction (for terrestrial TV use RTRS coverage card service); operator settings (for cable TV you may need to enter network TV ID or symbolic speed).

💡

If Xiaomi TV doesn’t find digital channels, try manually adding multiplex frequencies to your region, for example, in Moscow, it’s 546 MHz (RTRS-1) and 490 MHz (RTRS-2).

Manual Channel Customization: When Auto Search Fails

If the automatic search didn't produce results or missed some channels, you'll have to manually adjust them, which is also useful if you know the exact parameters of the broadcast (for example, for satellite TV).

Instructions for Digital Television (DVB-T2):

1. Go to Settings → Television → Channel settings → Manual search.
2. Select the source of the signal: TV (DVB-T2).
3. Enter the multiplex frequency (e.g. 602 MHz for RTRS-1 in St. Petersburg).
4. Specify bandwidth: usually 8 MHz.
5. Click Search and wait for the channels to be found.

For cable TV (DVB-C), additional parameters from the provider will be required:

• 🔢 Symbolic speed (e.g, 6875 ks/s).
• 🔄 Modulation (usually 256) QAM).
• 📡 Networked ID (if required).

This data can be clarified:

• 📄 In contract with the operator.
• 💬 On the website or in the chat support provider.
• 🔍 Search by TV model and operator name (e.g., “Xiaomi Mi”) TV Q2 MTS setting»).

For satellite TV (DVB-S/S2), manual settings include:

1. Select a satellite (e.g. Eutelsat 36E for Tricolor).
2. Transponder frequency input (e.g. 12226 MHz).
3. Indication of polarization (Horizontal or Vertical).
4. Enter a symbolic speed (e.g., 27500).

4. IPTV setup on Xiaomi TV: an alternative to terrestrial TV

If you prefer watching TV over the Internet, Xiaomi TV supports IPTV – streaming channels over HTTP or IGMP. This does not require an antenna, only a stable connection to the network at a speed of 15 Mbps.

There are two ways to set up an IPTV:

1. Through the built-in Live TV app: Open Apps → Live TV. Select Add Playlist and enter URL (e.g. from Wink provider or MTS TV). Save and wait for the channel list to load.

Through third-party applications:

• 📺 SS IPTV — playlist-support.m3u.
• 🎬 OTT Player - a convenient interface with EPG (television).
• 🌍 Lazy IPTV — It allows you to sort channels by category.

How to sort channels:

• 🔢 Automatic sorting: Settings → Television → Channel sorting → By numbers or alphabetically.
• 🖥️ Manual sort: In the same menu, select Manual sort. Use the Up/down buttons on the remote to move the channel. Save the changes with OK button.