How to set up channels on Xiaomi Smart TV TV: guide

Xiaomi Smart TV — It's not just a TV, it's a full-fledged multimedia center that supports digital, analog and satellite broadcasting, but even experienced users sometimes have trouble setting up channels, where the signal disappears, the channels are duplicated, and nothing is found. In this article, we will analyze all the ways to set up TV channels on Xiaomi Mi. TV, Mi TV Stick and other models with PatchWall or Google TV, We also show you how to solve typical problems.

Whether you are connecting the TV to the cable TV, antenna DVB-T2 Or a satellite dish, the algorithm of actions will be similar, but with nuances, and we'll look at both automatic search (the simplest method) and manual adjustment for power users, and you'll also learn why some channels may not show even if there's a signal, and how to fix it.

Preparing the TV for channel settings

Before you start searching for channels, make sure your Xiaomi Smart is a good fit. TV I'm ready for this process:

• 📡 Connecting an antenna or cable: Make sure the cable is tightly inserted into the connector ANT IN (or RF IN) If you're using a satellite dish, check the connection to the connector. LNB IN.
• 🔌 Power and network connection: The TV must be connected to the network, and if you plan to update the list of channels over the Internet (for example, for the purpose of the Internet). IPTV), connect to Wi-Fi.
• 📺 Selecting a signal source: On the remote, press the Source (or Input) button and select TV (antenna DTMB (Digital broadcasting in some regions).
• 🔄 Resetting previous settings: If previously channels have already been configured and are not working correctly, it is better to reset the broadcast settings to factory (Settings) → Channels → Reset).

Pay special attention to the quality of the cable. Cheap or damaged cables can cause a weak signal, which either will not find the TV channels, or they will "split" into squares. TV Q1 or Mi TV Q2, Check if your model supports DVB-T2 (digital TV) — This information is in the characteristics of the device.

⚠️ Note: If you connect via a cable provider (e.g., Rostelecom or MTS), you may need to activate the TV in the operator’s personal account.

Automatic channel search on Xiaomi Smart TV

This is the easiest and fastest way to set up channels, suitable for most users if the signal is stable and there are no specific requirements (e.g. manual channel sorting).

Instructions for PatchWall TVs (most Xiaomi Mi models) TV):

1. Press the Settings button on the remote (cogwheel) → select Channels.
2. Go to Channel Settings → Search engine.
3. Select the signal source: Antenna (DVB-T/T2) — digitally TV; Cable (DVB-C) — for cable television; Satellite (DVB-S/S2) — satellite-plate.

If required, enter search options (for example, frequency for cable). TV — It can be checked with the provider).

Start the search

For Google TVs TV (for example, Xiaomi TV A Pro or Mi TV P1):

1. Open the Settings. → Channels and entrances → Channel setting.
2. Select Setting up air channels (or cable/satellite).
3. Please indicate the country (e.g. Russia or Ukraine for the correct list of channels).
4. Run Automatic Search.

Once the search is complete, the TV will save all the channels found, and can be sorted, renamed or removed from the Manage Channels menu.

The density of the cable connection to the connector

Selected the correct signal source (TV, not HDMI)

TV connected to the Internet (to update the list of channels)

No interference from other electrical appliances (microwaves, routers)-->

Manual Channel Configuration: When and How to Use

Auto-search doesn't always do the job, for example, if:

• 📶 The signal is weak and the TV can't see some channels;
• 🔄 Add a specific channel that is not automatically found;
• 📡 Non-standard broadcast frequency (e.g. local providers).

In these cases, manual adjustment will help. Here's how to do it:

1. Go to Settings → Channels → Channels → Manual search.
2. Select the signal type (DVB-T2, DVB-C or DVB-S).
3. Enter the settings manually: For etheric TV: specify the frequency of multiplex (for example, 546 MHz or 778 MHz - depends on the region). TV: Enter frequency, transfer rate (Symbol Rate) and modulation (QAM-256 This data must be provided by the provider. TV: Select a satellite (for example, Absolute 36).°E), enter transponder frequency, polarization and Symbol Rate.

Search

For convenience, you can use a frequency table for your region, for example, in Moscow and the region for the use of a frequency table. DVB-T2 Multiplexes are used at frequencies 546 MHz (RTMS)-1) and 778 MHz (RTMS)-2). In other regions, the frequencies may differ – check on the RTRS website.

⚠️ Note: If the manual search TV gives an error No signal, check: correctness of the entered frequencies (even a small typo will lead to failure); quality of cable and connectors (try to replace the cable with a new one); The presence of interference (turn off nearby working devices, for example, Wi-Fi router).

Satellite channels setup on Xiaomi Smart TV

If you use a satellite dish, the setup process will be more difficult than for an on-air or cable dish. TV. You will need satellite, transponder and signal parameters, which are usually provided by a provider (e.g. Tricolor, NTV-Plus or local operators).

Step-by-step:

1. Connect the cable from the plate to the connector LNB IN TV-wise.
2. Go to Settings. → Channels → Satellite channel configuration.
3. Select Add Satellite and specify its name (e.g. Absolute 36).°E or Yamal 90°E).
4. Enter the transponder parameters: Frequency (12226 MHz; polarization (horizontal or vertical); Symbol Rate (e.g, 27500); FEC (3/4 auto).

Run a channel search. If there's a signal, the TV will find the available channels.

After searching, you can sort channels into groups (for example, "Films", "Sports", "Children's") or block unnecessary channels.

Important: Xiaomi Smart TV supportive CI-modules for decoding paid satellite channels (for example, Tricolor or NTV-Plus.

Solving problems with channel setup

Even if you did everything right, there could be problems, and let's look at the most common ones and the ways to solve them.

If the TV finds channels but they don’t save after a reboot, try:

• 🔄 Reset channel settings to factory (Settings) → Channels → Reset);
• 📥 Update the TV firmware (Settings) → On TV. → Updating the system);
• 🛠️ Check the antenna for damage (especially if it is outdoors).

Sorting, renaming and managing channels

Once you've successfully searched for channels, you can edit the list: remove the unwanted ones, change the order, create favorites. Here's how to do it:

1. Go to Settings → Channels → Channel Management.
2. Select the channel you want to change and click OK on the remote.
3. Available action: 🔄 Move - change the position of the channel in the list; ✏️ Rename - give the channel a convenient name (e.g. "CTC") HD"); 🗑️ Remove the channel from the list; 🔒 Blocking – hide the channel from children (required) PIN-code).

chosen

Star.

Favourite

If you have a lot of channels, you can divide them into groups by subject.

1. In the Channel Management menu, select Create a Group.
2. Give the group a name (e.g., "Sport" or "News").
3. Get the right channels into it.

On Google TVs TV (for example, Xiaomi TV A2) The channel management interface may be different, but the principles are the same: a long tap on the channel in the list opens the editing menu.

💡

Update your channel list regularly (every 1-2 months) as providers may change broadcast frequencies or add new channels.

Setting up IPTV Xiaomi Smart TV

If you use IPTV (TV over the Internet, the setup will be different from traditional methods. You will need a playlist in the format.m3u or data for connection from the provider.

How to configure IPTV:

• 📺 Through the built-in application: Install the provider application (for example, MTS TV, Rostelecom). IPTV") login with your account login and password. Channels will appear in a special section of the application.
• 🔗 Through third-party players: Install a player that supports IPTV (Like, smart. IPTV, OTT Player or TiviMate. Download the playlist (.m3u) player URL-Save and update the channel list.

If you have a playlist file, you can upload it directly to some applications, like Smart. IPTV:

1. Open the app and write it down. MAC-address.
2. Go to siptv.app, enter MAC-address and download playlist.
3. Restart the app and the channels will appear in the list.

⚠️ Attention: Free of charge IPTV-Internet playlists may contain illegal content or malicious links. Use only official sources from your ISP.

FAQ: Frequent questions about setting up channels on Xiaomi Smart TV