Setting up TV channels on Xiaomi Mi TV P1: from autosearch to manual sorting

Introduction: Why setting up channels on Xiaomi Mi TV P1 requires a special approach

Xiaomi Mi TV P1 — One of the most popular smart TVs on the market, thanks to a combination of price, picture quality and functionality, but many users have difficulty setting up TV channels first. Unlike traditional TVs, where the process is often reduced to the press of a button, here you need to take into account the features of PatchWall firmware, regional settings and even the software version.

The main problem lies in the variety of signal sources: broadcasting (DVB-T2), cable-TV (DVB-C), satellite-plate (DVB-S) or IP-Each of these methods requires a different configuration, and the interface Mi. TV P1 For example, automatic search may miss some channels due to a weak signal, and manual adjustment will require knowledge of multiplex frequencies for your region.

In this article, we will look at all possible scenarios, from basic setup of air channels to solving typical errors such as no signal or search “hang”, and pay special attention to the hidden settings of the engineering menu, which allow you to fine-tune the tuner parameters, which is difficult to find in the official documentation.

Preparing the TV for channel settings

Before you start searching for channels, you need to follow a few preliminary steps, and ignoring them can lead to a malfunction of the tuner or an incomplete list of channels found.

First, make sure your Xiaomi Mi is a good one. TV P1 It's connected to the antenna or cable providers correctly (DVB-T2) Use a passive or active amplifier antenna (if you are far from the tower). For cable TV, make sure that the cable is securely inserted into the connector. RF IN If you're using a satellite dish, make sure you're connected correctly. LNB-plug-in SAT IN.

Second, update your TV firmware to the latest version. Outdated software may contain bugs in the tuner. To check if the version is up-to-date, go to Settings. → On TV. → Update. If you have an update, install it by connecting the TV to the Internet via Wi-Fi or cable.

• 📶 Check the signal level: there's a signal strength indicator in the channel settings menu. If it's below 50%, try moving the antenna or using an amplifier.
• 🔌 Use quality cables: cheap coaxial cables can cause interference, especially at high frequencies.
• 🌍 Select the right region: in the settings of the TV (Settings) → Region) state your country. This affects the list of multiplexes available.

⚠️ Note: If you connect to cable TV from a provider (for example, Rostelecom or MTS), check the search parameters: symbolic speed, modulation and frequency range. Without this data, automatic search may not work.

Automatic Channel Configuration: Step-by-step instructions

Autosearch is the easiest way to set up channels, but it doesn't always give you the perfect result (DVB-T2).

1. Turn on the TV and go to the main menu by pressing the Home button on the remote. Select the Settings section (cog icon).

2. Go to Settings → Channels → Channel setting → Search engine.

3. Select the signal source: Antenna (DVB-T/T2) broadcaster (DVB-C) cable-TV.

4.Click Start Search. The TV will automatically scan all available frequencies and save the channels found.

The process can take anywhere from 5 to 15 minutes, depending on the number of multiplexes in your area, and when you're done searching, the TV will suggest you save the channels you found.

• 📺 View the list of channels and remove unnecessary ones (such as radio stations or takeovers).
• 🔄 Re-run the search if some channels are missing (possibly due to weak signal).
• 📊 Sort channels by number or alphabet (more on this in the next section).

⚠️ Note: If after auto-searching, some channels are displayed without sound or image, check the settings of the Audiopath in the channel menu, AC3 or EAC3), which may not be supported by the TV.

Ensure that the antenna/cable connection is correct|

Select the correct signal source (DVB-T2/C/S)|

Update the firmware of the TV |

Check the signal level in the tuner settings-->

Manual Channel Customization: When Auto Search Fails

Automatic search doesn't always find all the channels available, but it can be related to:

• 📡 Weak signal on some frequencies;
• 🔄 Non-standard broadcast parameters (e.g., atypical modulation);
• 🚫 Blocking of individual channels by the provider.

In such cases, manual adjustment will help.

1. Go to Settings. → Channels → Channel setting → Manual search.

2. Select the signal type (DVB-T2, DVB-C or DVB-S).

3. enter the parameters manually:

4. Click Search. If a channel is found, it will be added to the general list. Repeat the process for all the missing channels.

For broadcasting (DVB-T2) The following multiplex frequencies are relevant in Russia (may vary depending on the region):

• 📌 RTRS-1 (First multiplex): 546 MHz or 578 MHz;
• 📌 RTRS-2 (Second multiplex): 498 MHz or 690 MHz.

Sorting and managing the channel list

Once the channels are set up, their list can be chaotic: duplicate numbers, uncomfortable order, or no favorite channels at the beginning. TV P1 There are tools for manual sorting.

1. Go to Settings. → Channels → Channel management.

2. Select the channel you want to move and hold the button. OK You'll be able to drag the channel to the right place on the list.

3.To remove unnecessary channels, select them and press Remove (the button with the basket on the remote).

You can also create selected lists:

• ⭐ Favorites List: Add Frequently Viewed Channels for Quick Access.
• 📁 Grouping by genre: some firmware allows you to create folders (for example, "Sport", "Children's", "News").

If you frequently switch between different signal sources (such as antenna and cable TV), use the Quick Switch function.

1. Press the Source button on the remote.
2. Select the right source (for example, TV for air channels or HDMI prefix).
3. Add the source to your favorites by holding the button. OK.

💡

If after sorting the channels are lost, try resetting the tuner settings: Settings → Channels → Reset the tuner settings, which will return the factory parameters without removing the channels found.

Solving Typical Problems When Setup Channels

Even after the correct setup, Xiaomi Mi users TV P1 You can face errors. Let's look at the most common ones and how to fix them.

1. no signal or channels are found

• 🔍 Check the antenna/cable connection. Try using another cable or amplifier.
• 📡 Make sure the antenna is pointed towards the TV tower (for on-air TV).
• 🔄 Reboot the TV: Settings → On TV. → Reboot.
• 📶 Manually check the signal level at different frequencies, if it's below 40%, the problem is the antenna or the distance to the tower.

2 Channels found, but no image or sound

• 🔊 Check the sound settings: Settings → Sound. → Audio track. It may have been an unsupported format (e.g. Dolby Digital instead of Dolby Digital). MPEG).
• 📺 Update the TV firmware – newer versions often fix signal decoding errors.
• 🔧 Reset the tuner settings: Settings → Channels → Resetting tuner settings.

3. Search "hangs" on a certain frequency

• ⏳ Wait 10-15 minutes – sometimes the process takes longer due to weak signal.
• 🚫 Eliminate the problem frequency from the search: in manual mode skip it.
• 🔄 Try searching with another signal source (for example, instead of using a different signal source). DVB-T2 choose DVB-C, if the cable is connected).

⚠️ Note: If after updating the firmware lost channels, try to roll back to the previous version of the software. To do this, download the old firmware from the official Xiaomi website and install it through Settings → On TV. → Local Update.

💡

If the TV does not find any channels, first check the performance of the antenna / cable on another device (for example, on an old TV set-top box), this will help to eliminate hardware malfunction.

Additional functions of the tuner: what can Xiaomi Mi TV P1

In addition to basic channel settings, Xiaomi Mi TV P1 It offers a number of hidden features that can be useful:

1.Ether recording USB-accumulator

The TV supports recording broadcast programs to an external hard disk or flash drive (format) FAT32 or NTFS). For that:

1. Connect. USB-port-to-port drive on the back of the TV.
2. While viewing the channel, press the Record button on the remote (or hold it). OK).
3. Select the recording time (from 30 minutes to several hours).

2. On/off timer

You can program the TV to automatically turn on your favorite channel at a given time, for example, to wake up to the morning news. → System system → Timer.

Parental control

If you have children in the house, you can block access to certain channels by password.

1. Go to Settings → Channels → Parental Controls.
2. Install. PIN-code (default: 0000 or 1234).
3. Select the channels that you want to block.

4. Engineering menu for fine tuning

For experienced users, there is a service menu where you can manually adjust the tuner settings to get there:

1. On the remote, press sequentially: Menu → Settings → All Settings → General.


2 Enter the code: 4725 (for some firmware versions - 1969).




3. Go to the "Tuner" or "DTV Settings" section.

Here you can change:

• 📶 Tuner sensitivity;
• 🔄 Parameters of demodulation;
• 📊 Priority of soundtracks.

⚠️ Warning: Do not change the parameters in the engineering menu without understanding their meaning. Incorrect settings can lead to loss of signal or failure of the TV.

FAQ: Answers to Frequent Questions