How to turn on Xiaomi Smart Air Fryer: a complete guide with photos and tips

The Xiaomi Smart Air Fryer is not just a kitchen appliance, it’s a real helper for cooking healthy and delicious food without excess oil. However, even with such an advanced device, users often have questions about how to turn it on correctly, what buttons to press, and what to do if the device does not respond to commands.

In this article, we will go into detail about all the ways to turn on the Xiaomi Smart Air Fryer, from the basic procedure to solving possible problems. You will learn how to start an aerogrill using physical buttons and the Mi Home mobile app, what indicators should burn when working normally, and what errors like a flashing screen mean, and we will also give tips on first use to avoid typical errors and prolong the life of the device.

Preparation of Xiaomi aerogrill for the first inclusion

Before you turn on the Xiaomi Smart Air Fryer, you need to follow several mandatory steps, neglecting them can lead to malfunctioning of the device or even failure, starting with unpacking and checking the equipment.

The air grill box must contain:

• 📦 Xiaomi Smart Air Fryer (model) MJXJSQ01ZM or similar)
• 🔌 Network cable with a fork (length usually 1–1.2 m)
• 📄 Instructions for operation (in Chinese) + brief guide in English)
• 🍳 Basket for non-stick products
• 🔧 Removable grille (in some trim levels)

After unpacking, inspect the device for damage: check the integrity of the housing, the power cord and the internal chamber. Pay special attention to the ventilation holes - they should not be clogged with dust or protective film. If you notice a factory sticker on the heating element, it should be carefully removed.

⚠️ Warning: Do not connect the air grill immediately after delivery in the cold season. +5°C, let it warm up to room temperature for 1-2 hours.

It is also recommended that before the first inclusion:

• 🧼 Wash the basket and grille with warm water with a soft detergent (without abrasives!).
• 🧻 Wipe the inner chamber with a wet wipe, then dry.
• 🔌 Make sure that the socket meets the requirements of the device (220V, 10A, with grounding).

💡

If you smell bad plastic on the first turn on, it's normal -- this is how the residues of the factory lubricant burn out. Warm the aerogrill idle for 10-15 minutes at 200.°C with an open lid to eliminate the smell.

Xiaomi Smart Air Fryer: buttons and indicators

The easiest way to turn on an aerogrill is to use physical buttons on the front panel. Let's take a step-by-step process for the model. MJXJSQ01ZM (It is also relevant for other versions with touch control).

The control panel is located:

• 🔘 Power button (usually with an icon) ⊙)
• 🔄 Temperature control buttons (+/–)
• ⏱️ Time setting buttons
• 📊 Mode select button (e.g. Air Fry, Bake, Roast)
• 🔥 Quick Start button (in some models)

To activate the device:

1. Connect the power cord to the aerogrill and insert the plug into the socket.
2. Press and hold the power button (⊙) for 2-3 seconds until the indicator lights up on the display.
3. Wait for the beep (one short beep) – this means that the device is ready for operation.
4. Select the cooking mode with the Mode button (e.g. Air Fry for frying).
5. Set the temperature (usually 160-200)°C) and time (10-30 minutes) by buttons +/–.
6. Press the power button again to start the process.

The display shall show:

• 🔥 Current temperature (e.g. 180)°C)
• ⏱️ The remaining time (e.g. 00:15)
• 🔄 Fan indicator (blinks during heating, burns constantly during cooking)

Make sure the cart is installed correctly|Close the lid before you click.|Check that the ventilation holes are not closed|Do not place products above the maximum mark-->

If nothing happens after pressing the power button, check:

• 🔌 Connect to the socket (try another power source).
• 🔋 Cord condition - whether there are inflections or damage to the insulation.
• 🔒 Locking the lid (in some models, the device will not turn on if the lid is not closed before clicking).

Enable via Mi Home: Step-by-step instructions

One of the key advantages of Xiaomi Smart Air Fryer is the ability to control through the Mi Home mobile application (or Xiaomi Home in newer versions), which is convenient for remote start-up, selection of recipes and monitoring of the cooking process.

First, make sure that:

• 📱 On your phone installed Mi Home app (you can download from the App Store or Google Play).
• 📶 Air grill and phone connected to the same Wi-Fi network (2.4 GHz!).
• 🔋 The device is plugged into the socket and is in standby mode (power indicator burns).

Follow the instructions:

1. Open the Mi Home app and log in (or sign up).
2. Press + in the upper right corner, then select Add device.
3. In the list of categories, find the kitchen. → airgrill → Xiaomi Smart Air Fryer.
4. Press Connect and follow the instructions on the screen. The device should emit an audible signal.
5. Connect to a temporary Wi-Fi network that the aerogrill will create (the name will be type) XIAOMI-XXXX).
6. Return to the app and select your home Wi-Fi network (2.4 GHz! only).
7. Wait until the connection is completed (it can take up to 2 minutes).

Once connected successfully, the aerogrill will appear on the list of devices.

• 🔥 Turn the device on/off remotely.
• 📊 Choose from pre-loaded recipes (e.g. French fries, Chicken wings).
• ⏱️ Set the timer and temperature from the smartphone.
• 📈 Tracking the history of use.

With buttons on the device.|Through the Mi Home app|And both.|I haven't used it yet.-->

If the app doesn’t find the device, try:

• 🔄 Reboot the aerogrill (remove the plug from the socket for 10 seconds).
• 📶 Switch your phone to mobile data and back to Wi-Fi.
• 📱 Update the Mi Home app to the latest version.
• 🔧 Reset the aerogrill settings (hold the power button for 10 seconds until the double signal is given).

Decoding of indicators and sound signals

Xiaomi Smart Air Fryer is equipped with a light and sound display system that helps to understand its condition.

The following indicators are located on the front panel:

Sound signals:

• 🔊 One short beep – on/off, command confirmation.
• 🔊 Two short beeps – finishing the preparation.
• 🔊 Long signal – error (e.g., the lid is open while running).
• 🔊 Repetitive signals – critical fault (reset or repair required).

If the indicator ⚠️ It flashes red, which could mean:

• 🔥 Overheating (usually due to clogged vents).
• 🚪 The lid is not tightly closed.
• 🔌 Nutrition problems (tension surges).
• 🤖 Firmware failure (solved by restarting).

⚠️ Note: If there is a mistake after resetting E1 or E2 (codes displayed on the display) does not disappear, do not try to disassemble the device yourself.

Frequent Errors When Enabled and How to Avoid Them

Even experienced users sometimes face problems when turning on Xiaomi Smart Air Fryer. Let’s consider the typical errors and ways to fix them.

Error 1: The aerogrill does not turn on after connecting to the socket

Possible causes:

• 🔌 Faulty cable or socket (try another power source).
• 🔋 The internal fuse worked due to a voltage jump (reset is needed).
• 🤖 Firmware failure (update the software via Mi Home).

Error 2: The device turns on, but immediately turns off

This is most often related to:

• 🚪 A loosely closed cover (check the locker).
• 🔥 Overheating (let cool for 15-20 minutes).
• 🧲 Protection from children (in some models there is a lock buttons).

Error 3: Mi Home management is not working

Problems with connecting to Wi-Fi are solved as follows:

• 📶 Reconnect the aerogrill to the network (forget the device in the Wi-Fi settings of the phone and repeat the procedure).
• 🔄 Reboot your router (sometimes changing your Wi-Fi channel to 1-6 helps).
• 📱 Update the Mi Home app and aerogrill firmware.

Error 4: On the display flashes E1 or E3

These codes mean:

• E1 — Temperature sensor problem (try resetting your settings).
• E3 — Failure of the heating element (service required).

💡

If the aerogrill makes unusual sounds (cracking, humming) or smells of a burn, immediately disconnect it from the network and do not use it until checked at the service center.

To avoid most of the problems:

• 🧹 Regularly clean the ventilation holes from fat and dust.
• 🔌 Use only the original power cable.
• 📱 Update your firmware through Mi Home when notifications appear.
• 📖 Keep instructions or take a picture QR-box code for quick access to documentation.

Firmware Update: Why It Matters and How to Do It

Firmware (built-in software) is responsible for all of Xiaomi's Smart Air Fryer features. Regular updates fix bugs, add new cooking modes and improve stability. Neglecting updates can lead to failures, such as the inability to turn on the device or connect to Wi-Fi.

You can check and update the firmware in two ways:

Method 1: Through the Mi Home app

1. Open Mi Home and select your aerogrill.
2. Go to the device settings (cog in the upper right corner).
3. Press firmware update.
4. If a new version is available, click Update and wait until it is completed (don’t disconnect the device from the network!).

Method 2: Manually via Xiaomi website

If the automatic update does not work:

1. Download the latest firmware for your model from the official website.
2. Unpack the archive and copy the file to the flash drive (FAT32).
3. Put the flash drive in. USB-Air grill port (if any) or use OTG-adapter.
4. Press the power button for 5 seconds – the device should detect the file and start updating.

⚠️ Warning: Do not turn off the aerogrill during a firmware update. This may lead to the "bricking" of the device, and it will have to be handed over to the service for flashing through the firmware. JTAG.

Following a successful update:

• 🔄 The device will reboot automatically.
• 📱 Mi Home will be a notification of successful installation.
• 🎉 New modes may be added (e.g., Dehydrate for fruit drying).

Safety at first incorporation and operation

The Xiaomi Smart Air Fryer is an electric appliance with a heating element, so compliance with safety regulations is critical. Here are the key points to know before you first turn on and during use.

Installation rules:

• 🪑 Place the device on a flat, stable and non-combustible surface (table top, cabinet).
• 🧱 Do not place near the wall or furniture - leave at least 10 cm of free space for ventilation.
• 🚫 Avoid direct sunlight and wet spaces (such as near a sink).

Precautions for work:

• 👶 Do not leave the appliance unattended if there are children or pets in the house.
• 🧤 Use grips or silicone gloves when removing the basket – it heats up to high temperatures.
• 💧 Do not immerse the body in water! Use a wet cloth to clean.
• 🔌 Do not use extension cords - connect directly to the socket.

What to do in emergency situations:

• 🔥 If smoke is coming from the device, immediately disconnect it from the network and open the windows.
• 💥 If you lose control (does not respond to buttons) - pull the plug from the socket and wait for cooling.
• 🚑 If you are affected by electric current - de-energize the device and consult a doctor.

Unlike conventional aerogrills, Xiaomi Smart Air Fryer has an automatic shutdown function when overheating, but it only works at critical temperatures (above 240).°C. Don't rely on it alone, always watch the cooking process.

FAQ: Answers to Frequent Questions