Xiaomi Redmi Note 7 deservedly received the status of a popular favorite due to the successful combination of performance and price, but time does not spare even the most reliable devices. Over time, the capacity of the lithium-ion battery inevitably decreases, leading to rapid discharge, sudden shutdowns during load and bloating. If your phone stopped holding charge during the working day, replacing the battery will be the only effective solution to the problem.
Self-repair requires precision and understanding of modern electronics, as the adhesive design of the case does not require easy access to internal components. Owners need to prepare to work with heating elements and thin plumes, damage to which can permanently disable the gadget.
In this guide, we will discuss in detail each step of dismantling the back cover, turning off the plumes and installing a new energy cell. You will learn what tools are required to use, how to safely separate the glass from the frame and what to pay special attention to when building.
Diagnostics of the state of the battery and preparation of tools
Before you start disassembling, you need to make sure that the problem lies in the wear of the chemical element, and not in the software failure or malfunction of the power controller. Redmi Note 7 often encountered software bug showing the wrong percentage of charge, so first you should calibrate or reset the settings. If the phone turns off at 20-30% charge, warms up in the camera area or the back cover has moved due to inflated battery, repair is inevitable.
To successfully perform the operation, you will need a specialized set of tools that can be purchased from radio parts stores or ordered online. Lack of suitable equipment often leads to damage to the body or injuries, so do not rely on improvised tools like knives or forks.
- 🔧 Set of screwdrivers (cross-haired) PH000 and Phillips) for spinning the screws of the board.
- 🌡️ Thermoheating table or hair dryer for softening the glue under glass.
- 💳 Plastic card or mediator for safe opening of the case without scratches.
- 🧪 Isopropyl alcohol and new adhesive layer (B-7000 double-scotch).
- 🧲 Magnetic mat for sorting screws of different sizes.
Special attention should be paid to safety, as a damaged lithium-ion battery can catch fire if punctured. Work in a well-ventilated room and keep a fire extinguisher or sand container handy in case of an emergency.
⚠️ Warning: Never try to remove the battery if it is too swollen and occupies more than 10% of the body volume - in this case there is a high risk of fire during deformation.
The process of disassembling the case and access to the board
The first step is to carefully separate the back glass panel from the metal frame, which is held on a powerful adhesive layer. heat the back of the device to a temperature of 80-90 degrees Celsius, evenly warming the perimeter for 3-5 minutes. Do not keep the hair dryer too close to the glass to avoid its local overheating and cracks, which can occur due to a sharp temperature drop.
After enough warming up, insert the suction cup into the bottom of the lid, pull up slightly, and insert a thin plastic blade into the resulting gap. Move the tool along the perimeter, periodically warming the resistance sites until the glass is completely separated from the frame. Be extremely careful at the top of the smartphone, where the display plumes and fingerprint scanner pass under the glass.
When you remove the lid, you will have access to a metal screen that covers the motherboard and the plumes. To access the insides, you need to twist all the screws around the perimeter of the screen, their number can vary depending on the revision of the board. Carefully remove the metal plate, trying not to damage the antenna contacts soldered to it.
☑️ Postmortem readiness
Now you need to disable the plume of the main camera module and fingerprint scanner if it interferes with further access. On the Xiaomi Redmi Note 7, the scanner is often located on the back cover, and its plume passes through the notch in the frame, which requires special care when lifting the cover. Use tweezers or a plastic blade to snap connectors, avoiding excessive force.
Dismantling the old battery and cleaning the niche
Once you get access to the interior, you'll see a black rectangle of the battery that's glued to the bottom of the case with double-sided tape. Unlike the older models, there's no easy-to-reach pulling tongues, so you'll have to be patient and use chemical solvents. Wet the battery perimeter with isopropyl alcohol or a special glue-eating fluid, giving it time to penetrate the adhesive layer.
To extract the battery, use a thin plastic card or a special fishing line, carefully putting the battery on different sides. It is strictly forbidden to use metal tools such as blades or screwdrivers to smack the battery, since a puncture of the shell will cause an instant ignition of the electrolyte. If the battery sits very tightly, you can slightly warm the lower part of the body with a hairdryer, but do not exceed the temperature of 60 degrees.
| Parameter | Original battery | Chinese copy (Low cost) | Quality analogue |
|---|---|---|---|
| Capacity | 4,000 mAh | 2500-3000 mAh | 4,000+mAh |
| Cycle resource | 500-800 | 200-300 | 500-600 |
| PCB protection | Complete. | Absent. | Basic |
| Price. | Tall. | Low. | Medium |
Once the old battery is removed, the seat must be thoroughly cleaned of the residues of old glue and tape.The surface must be perfectly smooth and fat-free so that the new adhesive layer lies evenly and provides a reliable fixation. Use a lilac-free napkin dipped in alcohol for the final wipe of the niche.
⚠️ Warning: Do not throw your old battery into a regular trash can – take it to a special e-waste disposal facility.
Installation of a new battery and assembly of the device
Before installing a new component, make sure its connector matches the original connector on the Redmi Note 7 board. Visually compare the location of the contacts and the overall geometry, as even a millimeter mismatch can lead to a short circuit or the inability to close the lid. Apply a new layer of glue (B-7000 or special tape) on the case, distributing it in a thin even layer.
Carefully place the battery in a niche, matching the connector with the connector on the motherboard, and slightly press your fingers around the edges for locking. Don't plug the plume right away to the end - first make sure the battery is flat on the seat and doesn't bulge anywhere. After checking, gently snap the connector to a characteristic click, controlling the force to avoid breaking the fragile contacts.
Now you can start the reverse assembly: set the metal screen in place, twist all the screws in the correct order and connect the plumes of the display and scanner. Before the final sticker of the back cover, it is recommended to start the device first to ensure that the system is working and the charge is displayed correctly.
What if the phone doesn’t turn on after replacement?
Testing and calibration of the new battery
After successful assembly and first activation, a series of tests must be performed to verify the quality of the work performed. Charge the device to 100% and monitor the rate of charge collection - it must correspond to the declared power of the standard charger. Rapid heating in the battery or board area during charging may indicate problems with the controller or poor quality of the element itself.
To accurately diagnose the status of the new battery, you can use an engineering menu or special monitoring applications such as AccuBattery or Ampere. These utilities will show the real capacity, current voltage and wear rate, which will allow you to assess the quality of the installed part. In the Xiaomi engineering menu, you can run a hardware test by selecting the battery checkpoint.
It is recommended to perform a full charge-discharge cycle: discharge the phone before turning off, then charge to 100% when turned off, this procedure will help the power controller to correctly calibrate the percentage readings and prolong the life of the new battery. Repeat the cycle 2-3 times for best results.
💡
For maximum longevity batteries, try to keep the charge in the range of 20-80% and avoid deep discharges to zero in everyday use.
Frequent replacement errors and precautions
One of the most common mistakes of beginners is neglecting the heating of the case, which leads to cracks in the back cover when trying to force open.The glass on the Redmi Note 7 is quite brittle, and without properly softening the glue, the risk of damaging it is more than 50%.Always take enough time to warm up and take your time to separate the panels.
Another critical mistake is the use of substandard battery analogues, which may not have built-in protection against overheating and overcharging. Cheap copies often have a real capacity of 2-3 times lower than claimed and fail after a few months of operation.
- 🚫 Do not use superglue to fix the lid – it breaks down plastic and makes re-repair impossible.
- 🚫 Do not leave your phone unattended immediately after battery replacement.
- 🚫 Don’t ignore the bloating of a new battery – it’s a marriage that requires immediate replacement.
Remember that leakproofing the case reduces the waterproof device, so avoid getting water on the smartphone after repair. If you are not confident in your abilities, it is better to entrust the procedure to professionals in an authorized service center.
⚠️ Note: Use of non-original parts may lead to unstable system operation and loss of warranty if it is still in operation.
💡
A quality battery replacement returns 90-95% of the original battery autonomy if the original or certified counterpart is used.