How to turn on the external battery Xiaomi Mi Power Bank

When all the indicators flash quickly at the same time, protection against short circuit or overloading usually works. This means that the connected cable or device consumes more power than allowed, or there is a circuit circuit circuit.> First activation of a new device If you have just unpacked an external Xiaomi battery, the first thing you need to do is eliminate the transportation mode. Manufacturers specifically do not charge devices to 100% before sending to warehouses for safety. Often the charge level is about 60%, but the output is blocked. For primary activation, you need to connect the power bank to a powerful power source. Use the original cable or a high-quality analogue from the power supply liner with a fast transmission device with a power supply liner, and a fast transmission jack 2. At this point, no lights can go off, which is normal, because the controller is waking up. 15-20 After a short recharge, try to start the device. Press the on button once. If the lights catch fire, the activation cycle is successful. If there is no reaction, try pressing the button on the on button once. 10-15 Some models with low current (headphone or fitness bracelet charging) require double pressing. ☑️ Activation check Connect to powerful charging Leave to 20 Use high-quality cable Check the button response: 0 / 4 What to do if power bank is discharged in zero The situation when power bank Xiaomi is completely discharged and stopped turning on, is often found. Deep discharge of lithium batteries is dangerous, so the controller goes into protective mode, disabling the circuit completely. In this state, the device may not respond to a short press of a button. It requires a "push" to raise the voltage on the cells to the operating level. For resuscitation, connect the discharged Mi Power Bank to a power source with a current of at least 2A. It is important to use a good cable that is guaranteed to conduct current. 1 before 2 If you have a little bit of a power pump, you have to use the power bank to get the minimum charge you need to start the control system. If you still don't have a reaction after two hours of charging, you have to use the swing method. 5 Just a minute, then turn it off and plug it back in. 3-4 Sometimes it helps to rock the controller. You can also try to connect the device to USB-Smaller currents are sometimes better perceived by the deep discharge protection circuit. Low current mode and double press Many modern models of Xiaomi Mi Power Bank (especially the Slim, Pocket and Pro versions) are equipped with a low-power charging function. Bluetooth headsets, fitness trackers and some headphones consume less than 100 mA. A standard controller can perceive such low consumption as no load and automatically turn off the output after 30 seconds to save energy. To solve this problem, Xiaomi power banks have a special mode. To activate it, you need to press the switch on twice in a row. After double pressing, the indicators can start running or burning in a special mode, signaling the transition to low-current mode. In this state, the device will not shut down automatically, even if the consumption current is minimal.Switching off from this mode is also done by double tap or single, depending on the model.This is especially true for owners of wireless headphones.Diagnostics of malfunctions through indicators Understanding the signals that the indicator panel provides is the key to successful diagnosis. Xiaomi models use LEDs to communicate with the user. If you see a blink, color or lack of glow, this is not an accident, but an encoded message from the system. Consider the main states of the indicators in the table below.Please note that the exact color gamma that the Mi Bank can differ from the specific model of the Power 2S. Indicators state value Action Mitigate all 4 indicators Connection error or short circuit Check cable and connector device Burns 1 indicator (without blinking) Low charge level (less than 25%) Put on charging Indicators run around the circle Small currents or charging process Normal operation when pressing Deep discharge or locking Long-term charging from a powerful unit One indicator flashes slowly The charging process of the powerbic itself Expectation of full charge If you observe the behavior not described in the instructions, this may indicate the battery failure, and often the problem is required in the battery, but the battery itself is often used in the overload. Cables. USB They're subject to wear, fractures and oxidation of the contacts. Cheap cables can have poor wire cross-sections, which causes the voltage to drop, and the Xiaomi controller blocks the power supply, considering the load to be critical. USB-The connectors often get dust, pile from pockets and small debris. This creates resistance and prevents close contact. Carefully, using a wooden toothpick or plastic spatula (not metal!), clean the port. USB Type-C or Micro-USB. Blow the connector with compressed air. It's also worth checking the connectors on the device that charges the most. If the phone has a loose port, the contact can be unstable, causing the power bank to constantly turn on and off. Try connecting another device to the power bank (such as a lamp or other phone) to rule out the problem of the cable or source port. ⚠️ Warning: Never use metal objects (needles, paper clips) to clean ports USB. This can lead to short-circuiting of the contacts inside the connector and irreversible damage to the power controller.Resetting settings and restarting the system In rare cases, the software part of the controller can freeze. Although power banks don't have an operating system as we know it, the controller microcode can go into error. To reset the logic state, you have to reboot the circuit completely. Disconnect all cables from the device. Press and hold the power button during the time. 30 Release the button. Connect the power bank to the charger on the 5-10 Then turn off the charge and try to turn it on again, and this sequence of actions helps to reset the error flag in the controller register. If you have access to the multimeter, you can check the output voltage. If you press a button, the voltmeter shows a jump to 5 volts and immediately drops, then the protection works. If the voltage 0 volts even with a charged battery is likely to malfunction the controller or a break in the inside of the case. When professional repair is required, despite the reliability of Xiaomi, the electronics are not immune to defect or fall consequences. If none of the above methods help, and the device remains “dead” after a long charge from different sources, the charge controller is likely to fail or a deep degradation of the batteries. Inflated one of the battery, the battery is degraded from the battery. Also, the reason for contacting the service is overheating. If during normal charging the device heats up to temperatures unpleasant to the hand (above). 50-60 It's an internal short circuit or a faulty balancing circuit. Self-repairing at home is complicated by the monolithic design of many models. Why doesn't Xiaomi power bank charge the phone even though the lights are on? Probably the problem is the cable or low current mode. Try replacing the cable with a higher quality one with thick veins. If you charge the headphones, double-press the on button to activate the low current mode. Also check if the port of the phone is contaminated. How long does Mi Power Bank charge? 10000 The charging time depends on the power of the adapter. 5V/2The process will take about 5-6 hours. If you use a Quick Charge 3.0 or Power Delivery adapter, the time is reduced to 3-4 hours. Using weak units (5V/1A) can increase the time to 10-12 hours. Can you leave Xiaomi powerbank on overnight charging? Yes, modern Xiaomi controllers have recharge protection. Once the battery reaches 100%, the current will stop automatically. However, to extend the life of lithium cells, it is recommended not to keep the device on charging constantly after full filling. What does the first indicator flash when you connect the cable? This is a regular self-testing process and start charging. If the first indicator flashes, the cable flashes, then the power stops, the controller starts flashing, then the lighting starts. ⚠️ Warning: Do not attempt to open the case of the power bank if the device is under warranty. Violation of seals or opening marks on the screws (if they are under the stickers) will be grounds for denial of warranty service.