Owners of the Redmi Note 8 smartphone often wonder about the possibility of using wireless power transmission technology, as this greatly improves the comfort of the gadget. Unfortunately, the standard equipment of this popular device does not include an integrated inductive charging module, which forces users to look for alternative solutions for their Xiaomi.
There is a proven and safe way to implement this feature in your device using a special receiver-adapter that connects through the USB Type-C connector. In this article, we will discuss in detail the process of selecting compatible equipment, the stages of physical installation and software configuration of the system for proper operation with Qi protocols.
Implementing wireless charging requires attention to detail, as substandard components can damage the power controller or the battery itself.We have prepared a step-by-step guide to help you avoid common mistakes and successfully upgrade your Redmi Note 8 without losing warranty on other nodes of the device.
Compatibility analysis and equipment selection
The first step before any manipulation is a careful selection of components, as not all receivers work equally well with the MIUI shell. You will need to purchase a special thin receiver (receiver) standard Qi, which has a USB Type-C connector corresponding to the port of your smartphone.
Pay attention to the thickness of the module: too thick a plate can interfere with the tight fit of the back cover or cause it to crack when installed. Modern models of adapters for Xiaomi are less than 1 mm thick and easily hide under the body.
💡
When buying a receiver, make sure that it maintains a charge current of at least 1A, otherwise the process of replenishing energy will occur extremely slowly.
It is important to consider that there is no built-in support for wireless charging in the Redmi Note 8 motherboard, so all the logic of the work falls on the external receiver board and Android software. When choosing, pay attention to the presence of protective mechanisms against overheating and overcharging.
- 📏 The thickness of the receiver shall not exceed 0.8-1.0 mm to keep the shell tight.
- ⚡ Support for fast charging protocols (if your power supply and receiver allow it).
- 🔌 Exact match of connector USB Type-C (not to be confused with Micro-USB).
- 🛡️ Availability of built-in safety controller to protect the battery.
Preparation of the workplace and tools
To successfully install the module, a clean and well-lit workspace free of static electricity must be provided, and dust and small particles trapped under the back cover or on the contacts can short-circuit or degrade the heat sink.
You'll need the minimum toolkit that most home craftsmen have, but there are high demands on their quality. Using metal objects to snap the case can damage plumes or break glass, so it's better to use specialized plastic blades.
☑️ Preparation for installation
Before starting work, be sure to turn off the device by pressing the power button and selecting the appropriate item in the menu, which is critical to prevent short circuits when the receiver connects to the USB Type-C port.
The process of installing the receiver Qi in the housing
The most difficult step is to carefully open the back cover, which in the Redmi Note 8 is glued around the perimeter to a special glue. To soften the adhesive composition, it is recommended to warm the edges of the body with a hairdryer to a temperature of 40-50 degrees, but do not overheat the glass so that it does not burst.
Use a plastic card or a spatula to walk around the perimeter of the device, gradually peeling off the lid. Don't try to open the phone from one corner, act evenly, moving around in a circle so as not to break plastic latches if they are present in the structure.
Once the lid is removed, you will see the battery and the lower board where you need to put the receiver, the receiver plume is carefully laid along the side facet or under the battery (thickness permits), and the connector is inserted into the charging port.
⚠️ Attention: It is strictly forbidden to make excessive efforts when inserting the receiver connector into the charging port. USB Type-C on the motherboard, the repair of which will cost more than the receiver.
Make sure the receiver is flat and not squeezed anywhere. If you use double-sided tape to lock the module onto the battery, make sure it doesn't overlap the vents or sensors.
Performance check and diagnosis
After the physical installation of the module, take your time to immediately glue the lid to the dead. First, test the start by connecting the smartphone to the wireless charging base. The indicator on the phone should signal the start of the charging process.
Android usually has a notification or audible signal about the connection of the wireless charger. If this does not happen, check the density of the receiver to the base and the correct connection of the plume to the port.
What to do if the charging is jerky?
For a deeper diagnosis, you can use an engineering menu or special applications that display voltage and current strength. Enter the dialer code ##6484## to enter CIT testing mode, where you can check the status of the battery.
| Parameter | Normal value. | Problematic significance | Action. |
|---|---|---|---|
| Connection status | Connected | Disconnected | Check the connector |
| Charge current | 0.5 - 1.0 A | 0.0 - 0.1 A | Replace the base |
| Temperature. | 30 - 40 °C | > 45 °C | Remove the case |
| Tension. | 4.2. to 4.4 B | < 4.0 Included | Check the cable. |
System setup and optimization
After a successful physical connection, it is important to properly configure the software part so that the system correctly recognizes the power source. In some versions of MIUI, you may need to activate debugging mode or install third-party utilities to display the status of wireless charging.
Go to Settings → About Phone and click on the MIUI version several times to activate the developer menu. Then, in the advanced settings, look for the item related to power management and make sure that there is no limit to the background activity of the charge processes.
To optimize the operation, it is recommended to calibrate the battery after installing new equipment. discharge the phone to 0% (until it turns off), then put it on wireless charging and charge to 100% without interrupting the process.
Wireless charging is always accompanied by heat, and an additional receiver inside the Xiaomi case can enhance this effect. Use lightweight cases or remove them while charging.
Frequent problems and methods of their elimination
One of the common problems is that the contact is unstable, when the phone starts charging and stops, most often because the receiver connector is not fully inserted into the port or the contacts have oxidized.
Another problem is overheating. If you notice that your phone is getting very hot, try lowering the charging base or using active cooling (fan), and prolonged overheating is bad for lithium polymer battery chemistry.
- 🔄 Cyclical Connection: Check the cleanliness of the port USB Type-C from pile and dust.
- 🔋 Fast discharge: Make sure the receiver doesn't consume power when the phone isn't on base (parasitic consumption).
- 📱 Incompatibility of the case: Too thick or metal cover blocks the magnetic field.
⚠️ Attention: Using metal plates to mount in the car can shield the charging signal. Place the plate so that it does not overlap the area of the receiver coil (usually the center of the rear panel).
Safety and long-term operation
When the Redmi Note 8 is constantly in use, it is important to monitor the condition of the adhesive layer of the back cover. Frequent removal of the lid to check contacts weakens the adhesion, and the phone can lose protection from moisture and dust.
It is recommended to periodically (every 3-6 months) check the density of the plume. Vibration when carried in a pocket or bag can gradually loosen the connection, which will lead to loss of contact.
💡
Regularly checking the body temperature while charging is a major indicator of the health of your modified power system.
Remember that using uncertified accessories can affect your job. NFC-module if the coils are located close to each other. - Xiaomi Note 8 NFC-The module is often combined with the antenna located at the top, so the receiver at the bottom usually does not interfere with the antenna.
Comparison with wired charging method
The wireless method is convenient, but has its drawbacks compared to traditional cable, the main difference being the loss of power during transmission and the lower battery replenishment rate, especially if a cheap base is used.
But for overnight charging or navigating in-car, this method is indispensable, reducing mechanical wear and tear on the USB Type-C port, which is one of the most vulnerable parts of modern smartphones.