How to properly reboot Xiaomi Powerbank: all ways

Owners of external Xiaomi batteries sooner or later face a situation when the device begins to work incorrectly: it does not charge, does not give current or does not turn on. Most often, a simple reboot solves the problem, but how to do this correctly if the power bank does not have a power button or the screen does not respond? In this article, we will discuss all possible ways to restart power bank from Xiaomi, including hidden functions and hardware methods.

It's important to understand that the procedure can vary depending on the model. For example, Mi Power Bank 3 with USB-C has one reset algorithm, and Redmi Power Bank 10000mAh has another. We'll look at universal methods that are suitable for most devices, and also point out the nuances for specific lines. If your battery is not showing any signs of life, don't rush to throw it away, 80% of the time the problem is solved without repair.

Before you start restarting, make sure that the problem is not in the cable, charger or plug-in gadget. Try charging the power bank from another power supply and connecting another device to it. If the malfunction is confirmed, proceed to reset.

Why Xiaomi Power Bank May Need a Reboot

Xiaomi's external batteries have built-in protection, which sometimes goes off falsely, and here are the most common reasons why the device might freeze:

• 🔋 Deep battery discharge – if the power bank has been discharged for a long time, the controller blocks operation until the minimum voltage is restored.
• ⚡ Short circuit in the charging or discharging circuit that triggered the protection.
• 📱 Incompatible charger – use of a power supply with inappropriate parameters (for example, too high current).
• 🌡️ Overheating or hypothermia – working at extreme temperatures causes the system to shut down.
• 🔄 Failure of the firmware controller - rare, but occurs with sudden voltage surges.

In most cases, rebooting helps bring the device back to life, but if the power bank is physically damaged (bloating, cracking, burning smell), attempts to revive it can be dangerous - such a device should be disposed of.

Modern Xiaomi models (such as the Mi Power Bank 3 Pro or Xiaomi HyperCharge) have better controllers that are less likely to “glutch”, while budget options like Redmi Power Bank 5000mAh often require manual reset.

Method 1: Software reboot (for models with a button)

If your power bank is equipped with a physical power button (for example, Mi Power Bank 2C or Xiaomi Mi Power Bank Pro), use the standard procedure:

1. Connect the power bank to the power source (charger) using the original cable.
2. Press and hold the power button for 10-15 seconds.
3. Release the button when the indicators start flashing or go out.
4. Turn off the cable and wait 30 seconds.
5. Connect the power bank again - it should start charging.

On some models (e.g. Mi Power Bank 3), the button is hidden under a silicone plug, so you need to tuck it neatly with a nail or a plastic card. If the button is not pressed, don't put too much effort into it: there may be a lock inside that blocks the mechanism when it overheats.

Check the integrity of the cable and connectors

Use an original or certified charger

Make sure the power bank temperature is within 10–35°C

Do not connect the load during resetting.-->

If the indicators do not respond after holding the button, try repeating the procedure 2-3 times at intervals of 1 minute.

⚠️ Warning: Do not use metal objects to press a button - this can damage contacts.If the button is recessed and not pressed, it is possible that the power bank is in deep protection mode and another method will be required.

Method 2: Hardware reset (for models without a button)

Many Xiaomi budget models (e.g. Redmi Power Bank 5000mAh or Mi Power Bank 1) do not have a physical power button, in which case the reboot is performed through the manipulation of the connection:

1. Connect the power bank to the charger (preferably with a current of at least 2A).
2. Wait until at least one light comes on (this can take up to 30 minutes if the battery is severely discharged).
3. As soon as the indicator blinks or lights up constantly, quickly disconnect and reconnect the cable 3-5 times in a row.
4. Leave the device on charge for 1-2 hours.

This method simulates a controller reset due to sudden changes in voltage. If the indicators do not light up even after 30 minutes, try using another charger with higher current (for example, from a Xiaomi smartphone with Quick Charge support).

For USB-C models (such as Mi Power Bank 3), you can try an alternative:

1. Connect the power bank to a PC or laptop via USB-C.


2. Hold the Ctrl + Alt + Del keys on the keyboard (this creates a short-term reset of the USB- port).




3. Reconnect the connection 2-3 times.

This technique sometimes helps wake up the controller when it is in sleep mode, but it does not work on all devices and depends on implementation. USB-computer-side controller.

Method 3: Reboot through full discharge and charge

If previous methods have failed, try a full discharge and charge cycle, which is suitable for models that are switched on but are unstable (e.g., switched off when a load is connected).

1. Connect to the power bank the device with minimal consumption (for example, wireless headphones or fitness bracelet).
2. Wait until the power bank is completely discharged (all indicators are turned off).
3. Leave it in a discharged state for 1-2 hours.
4. Connect to the original charger and charge for at least 8 hours (even if the indicators show 100% sooner).

This method helps reset the controller calibration and restore the correct charge level readings, especially for older power banks that start lying with interest (for example, show 50%, and after a minute turn off).

For Quick Charge-enabled models (such as the Mi Power Bank 3 Pro), use a charger with similar technology to speed up the process and reduce the risk of re-failure.

⚠️ Warning: Do not use high-consumption devices (for example, laptops or tablets) to discharge, as this may cause the power bank to overheat.

Method 4: Reset via connection to another power bank

If your Xiaomi power bank doesn’t respond to network charging, but has a USB-C or Micro-USB connector, you can try waking it up with another external battery, which works because one power bank is applying voltage to another, bypassing the controller lock.

You'll need:

• 🔌 Other working power bank (of any brand) with connector USB-A.
• 🔗 Cable USB-A → USB-C or USB-A → Micro-USB (depending on the model).

Instructions:

1. Connect the “donor” power bank to your Xiaomi using a cable.
2. Wait 5-10 minutes. If the lights on your device light up, turn it off.
3. Connect to normal charging and wait for full recovery.

This method is especially effective for Mi Power Bank models. 2/2S, And if you don't have a second power bank, you can use it. USB-powered hub or even charging from a car lighter (via an adapter).

💡

If there is no second power bank at hand, you can use a charger from a laptop with a USB-The main thing is that the output voltage is 5V.

Table: Reboot methods for popular Xiaomi models

If your model is not listed in the table, focus on the type of connector and the presence of a button. For USB-C devices, methods 1 and 4 are usually suitable, for older models with Micro-USB methods 2 and 3.

What to do if nothing helps

If none of these methods worked, the problem may be deeper:

• 🔧 Charge controller malfunction – requires flashing or board replacement (in service center).
• 🔋 Battery degradation – if the power bank is more than 3-4 years old, the capacity may have fallen to a critical level.
• 💥 Short circuit inside the body - often accompanied by bloating or heating.
• 🔌 Oxidation of contacts - especially important after moisture.

In these cases, self-repair is not recommended - it is better to contact an authorized service center Xiaomi. the cost of diagnosis is usually 300-500 rubles, and repair (if possible) will cost 1000-2500 rubles, depending on the model.

If the power bank is under warranty (usually 12 months), do not open it yourself - this will void the warranty obligations. To check the status of the guarantee, you can use the official Mi Home application or the service.mi.com website.

💡

Before visiting the service center, take a photo of the serial number of the power bank (usually indicated on the sticker under the case) and the purchase check - this will speed up the application process.

If repairs are not cost-effective (e.g. for budget models under RUB 1,000), consider buying a new power bank.Modern models like the Xiaomi HyperCharge 120W or Redmi Power Bank 30W offer better crash protection and longer lifespan.

FAQ: Frequent questions about Xiaomi powerbank reboot